puck holder for magic band 3d models

Used with Magic Band 2.0 Print with watch strap down using back supports.

Magic Band 2.0 Puck Holder Print with watch strap down using back supports.

Used with Magic Band 2.0 Print with watch strap on bottom utilizing back supports.

Used with Magic Band 2.0 If using a bowden extruder, print slower (20ms).

I lost the screws from my original Halcyon magic band, but this sizing holds the back of the puck holder in firmly enough I'm not worried about it falling out. I originally meant to print the gold part in gold and the purple part in purple, but the...

This Magic Band holder printed with ender 3 and Geeetech A10M Printers is a gift I made for my sisters magic band collection that can hold around 15 bands and can be printed in 4 pieces. Each piece is printed at 100% and can also be scaled to fit...

going to disney and didn't want 2 straps on my wrist. ... insert the little puck from disney from the back then install on your watch band. ... needs to be TPU or TPE or something very flexible is a tight fit but you won't loose it.

Designed this holder for the pebble of Disney's Magic Band 2. I didn't like having to wear my watch on one arm and the Magic Band on the other so I figured I'd combine them. This only fits the gen 2 version of the Magic Band. It does not fit the new...

kids don't want to wear the disney magic band, I found a design by GordonInnovations, I add two ears, hope you like it.

Fun key ring attachment if you don't like wearing the traditional magic bands. ... just pops right into the design provided. Made the inside concave to perfectly hold and surround the little fob that is removable from the magic band 2.0

... ...For Z probing, we use a "puck" which we put on the PCB to make a circuit when the tool touches the PCB. This "puck" needed a holder, so I used FreeCAD to design such a holder, and printed it on my 3D printer. ... Not perfect, but good enough.

The Yeti can holder is awesome, but it is designed for 375ml cans. ...However, many craft beers come in 330ml cans. This puck drops into the Yeti can holder to make the 330ml can fit perfectly.

A holder for phone in landscape mode for the Sammsung charging puck. picture shows the iterations. one was a portrait version, the middle was the initial idea and it subsequently grew a crack on the first day of use. the 3rd is the final model.

A holder for phone in landscape mode for the Sammsung charging puck. picture shows the iterations. one was a portrait version, the middle was the initial idea and it subsequently grew a crack on the first day of use. ...the 3rd is the final model....

This is a small LED Puck holder I designed for my lithophane prints. I wanted to use a battery powered light but needed a way to stand it up. ...I like that I can control the distance of the light from the lithophane print for the best result.Link to...

This is a holder for a puck light I picked up at my local ace hardware. It was sold as a single light with no power supply (I just found a matching one in a drawer). Unfortunately I can't find a link to it to show you. I'm assuming it's a lot...

... to accommodate the exit angle of different pucks. Puck can be secured to this using double-sided tape and then this item to your Opterra using your favourite means of fixing. ... The arrow and the nick are intended to help you identify 'forward'.

... you like it. ... I used onshape for modeling. And a Prusa slicer for slicing. In the slicer, I rotated it by 4.5 degrees. I used less than 10 meters of filament and printed it around 11h. ... You can even sell the model if you say it's from me :)

This is a air hockey puck holder, use to hold air hockey pucks, but can be remixed or adapted foe other uses

Please note that the Magic Band puck can be removed from the watch strap holder but it will require some force. This is by design to prevent it from falling out. Edit 2-22-20: I updated the strap of the holder to be a bit thicker (v2). ...The previous...

magic band reader

holder for magic ball cover, under the tablet wood screew #8 1-1/2

Engagement ring holder designed to look like a Disney Magic Band

2.) Use a Phillips #000 ("triple zero", AKA very small) screwdriver to remove the two screws and backplate from the Magic Band v2 bracelet. 3.) Remove the RFID puck from the bracelet and put it into the 3D printed keychain. 4.) Attach the...

A Lock for your Magic Band To Use Properly put Lock on the Side with Holes and put the Magic Band on Normally, and Slide Lock Over and Past Mickey's ears to Lock the Sides Together. ... If You are Scared that it will Fall off try this Magic Band Lock...

This is a design for my magic band reader that can control appliances. In a time when the parks aren't that accessible, why not bring some disney magic home?! I have a tutorial of the rest of this build on my github linked below. Happy building!

I used a textured heat bed sheet, which left a nice texture on the "face". 2.) Use a Phillips #000 ("triple zero", AKA very small) screwdriver to remove the two screws and backplate from the Magic Band v2 bracelet. 3.) Remove the RFID puck from the...

This is a replacement band for the [Walt Disney World Magic Bands](https://disneyworld.disney.go.com/plan/my-disney-experience/bands-cards/). Simply [take out the icon](http://www.magicbandcollectors.com/wp-content/uploads/2016/11/IMG_2539.jpg) from...

Design of a Disney parks magic band reader. ...Assembly does require glue. You can find a video of how to assemble and configure a real magic band reader here: https://www.youtube.com/watch?v=IrjHKRolrVw

This is a simple holder for standard 58mm puck screen and the very thin sworksdesign puck screen. ...Has sufficient drainage and small enough to have it print in about 1h.