pulley small 3d models

Customized version of http://www.thingiverse.com/thing:175044 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=175044 Instructions Using the following options:...

You only need an 8mm bolt and nut that is long enough to reach through the bore to complete. ... Refer to drawing Dimensions.

Customized version of http://www.thingiverse.com/thing:363800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=363800 Instructions Using the following options:...

Very small chain idler or pulley (26mmØ) for a small chain with 2mmØ, 6mm width and 16mm in length.

Customized version of http://www.thingiverse.com/thing:175044 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=175044 Instructions Using the following options:...

These are small pulleys I print and stock in my makerspace for projects to use with rubber bands. ...The axle diameter is for 1/8" rods with a snug fit, the motor is designed for small DC motor drive shafts at 0.08".

This is a pulley I built to attach to a small motor. This pulley fits a Mabuchi RS-555 motor. This is a very common hobby motor used in RC Cars. The motor has a 3mm shaft size. Print this as-is using either PLA or ABS. Do at least 20% infill. ...

replacement pulley for babyliss twist

replacement pulley for babyliss twist

A model I made following along my professor in my Intro to 3D Modeling class at J.F. ...Drake State Community College.

Designed at J.F. ...Drake State Community & Technical college.

3D scan of the Sur Ron / Segway X160 X260 belt drive pulley - the small one that connects to the motor. ...Model is exactly to-scale so you can use it for measurements or reverse engineering - in mm unit scale.HQ_OG = High Quality Original (Gangsta)...

Customized version of https://www.thingiverse.com/thing:3013341 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3013341

Customized version of https://www.thingiverse.com/thing:3040728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3040728

small pulley

Just a small pulley system.

pulley for v belt

Pulley is a simple machine and comprises of a wheel on a fixed axle, with a groove along the edges to guide a rope or cable

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: no_of_nuts = 1 teeth = 8 m3_nut_depth = 2,7 pulley_b_ht = 2 additional_tooth_depth = 0 m3_dia = 0 nut_angle = 90 idler_ht = 1,5 pulley_t_ht = 4...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: additional_tooth_depth = 0 m3_nut_hex = 1 pulley_b_dia = 20 no_of_nuts = 1 pulley_b_ht = 8 additional_tooth_width = 0.2 m3_nut_depth = 2.7...

A generator for small pulley, perhaps it will also work for bigger belts etc.. . but i only tried with small diameter belts. The pulley in the photo is with the center part of the wheel floating in the middle, i changed that because i did not like...

These are covers that may be used to keep the string on pulley bearings used in a lift mechanism such as that available from REV Robotics (http://www.revrobotics.com/rev-41-1368/). They should work with similar bearings that have the following...

This is a small generic pulley I designed which can be used for many applications. I designed and printed it for raising and lowering some flourescent light fixtures. Instructions This prints well...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_nut_flats = 5.7 idler = 1 retainer_ht = 1.5 nut_angle = 90 m3_nut_hex = 1 additional_tooth_width = 0.2 retainer = 1 teeth = 10 idler_ht = 1.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: retainer_ht = 1.5 additional_tooth_width = 0.2 m3_nut_hex = 1 motor_shaft = 5.2 pulley_b_dia = 20 m3_nut_depth = 2.7 retainer = 1 profile = 12...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_ht = 0 idler = 1 motor_shaft = 8 additional_tooth_depth = 0 idler_ht = 1 retainer = 1 m3_nut_flats = 5.7 nut_shaft_distance = 1.2...

Five blocks of this type recovered from the site. ...They are small single sheaved blocks with a length of c.100mm some of which were found complete with ropes and formed a tackle.

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627

Customized version of https://www.thingiverse.com/thing:36568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=36568

Wheel on an axle designed to support movement of a belt.