push spring latch 3d models

<p>PLA 200/60</p><p>Fan 100%</p><p>no supports</p>

Mass = 1066.52

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI sketched out a circle of radius 6, and a line 18mm long on the left, and then 2 of 45degree angles, make sure the center of the circle to the bottom...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters For creating this drew this out from the blueprint provide and started sketching at first the circle I did not put at the origin so make sure to do...

I simple just followed the blueprint instructions, dimensioned the figure correctly then extruded the figure to the correct measurement.

Tools used: Smart dimension, line tools, circle tool, trim entitiesMass: 1066.52

Steps:1. Started the sketch o the 40mm ark and dimensioned as I went, when I got to the corner with the two tangent arcs, I made the horizontal line coming from the 45 angle coincident with the point of the 29mm arc.2. Extruded to part width3.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersFor 2D I used the line, fillet, and circular tool.For 3D I used the extrude feature.

Density = 0.01 grams per cubic millimeterMass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersFirst sketch your piece on the front plane then extrude it, and if need be do a extrude to next on the...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI started with the circle and worked around.

Test prep project

step1: sketch geometry according to the blue prints (( !! crucial !! ...- when sketching make sure the arcs are fully defined first, then make the line under the whole cut out concentric with the axis))(note) the axis point in the blue prints can be...

steps:1. created left edges sketch first2. added the curves, created relations and dimensions3. worked on right side of sketch4. added hole in left center of sketch5. added finishing relations with respect to the plus reticle thing6. extruded7.

This is an uncomplicated device designed to secure something in place. ...It's not exactly rocket science.

First, I started by sketching out the outline of the front view of the sketch. I used the dimensions in the blueprint to sketch out guidelines for me to use to sketch it out. I used the line tool and the center line tool the most in this project.

Use for Door Cabinet....

First I made a lot of dimensions to make it easier to sketch out, I started on the right slant and worked clockwise. ...After I made the sketch I extruded 45mm.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters Process:I sketched the whole part in just 1 sketch and then did the boss extrude. ...It was relatively easy it's just figuring out the dimensions.

This is one of 6 original parts I used for this assembly. The only changes I made for this part were to make it smaller so it can fit the size of the rest of the assembly. I used this part to create a 'locking' mechanism for the fridge. ...I was going...

Mass = 1066.52 gramsMake a sketch with a circle at the origin R6. Make a line to the left and underneath both 14 away. Make the left line 18 and between those a 45degree angle line. The bottom line running until a R5 circle's top. From that circles...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters

steps:1. created left edges sketch first2. added the curves, created relations and dimensions3. worked on right side of sketch4. added hole in left center of sketch5. added finishing relations with respect to the plus reticle thing6. extruded7.

a tool

I created this by measuring out the measurements on the front and extruding backwards.

CSWA part

Individual placed in second-ranked structure.

Second try