pvs14 eyepiece 3d models

I've posted more eyepiece designs here: https://www.thingiverse.com/thing:4580598 https://www.thingiverse.com/thing:4597001 Each eyepiece consists of the following parts: 1) 1.25" barrel with a 42.6mm dia. 1.5mm pitch external thread, 2) Housing...

20X80 Light weight binocular with 90 degree eyepieces

The stl files are for my Nagler Eyepieces, printed on Anycubic i3 Mega. - the bottom caps (green) are standard 1.25" or 2". Can be used for any other eyepieces. - the top caps (blue) are made for Nagler. I cannot promise it works on other...

I've posted more eyepiece designs here: https://www.thingiverse.com/thing:4597001 https://www.thingiverse.com/thing:4587751 Each eyepiece consists of the following parts: 1) 1.25" barrel with a 33mm dia. 1.5mm pitch external thread, 2) Housing with...

Visit my Homepage for more Information about the Smartphone Alignment Support for Baader Hyperion Eyepieces (german): https://make-astronomie.de/smartphone-alignment-support --- Viele Menschen sind begeistert, wenn sie das erste mal durch ein...

I've posted more eyepiece designs here: https://www.thingiverse.com/thing:4580598 https://www.thingiverse.com/thing:4587751 Each eyepiece consists of the following parts: 1) 1.25" barrel with a 1.5mm pitch external thread, 2) Housing with a matching...

... gap without issue. If bridging is not possible, low-infill support can be used instead. I personally find these replacement eyepiece covers to be more comfortable and secure than the original ones, which is why they have become my preferred choice.

I bought the SVBony 68 degree field-of-view (RED LINE) eyepieces and they kept popping out of my Barlow that has a cooper ring tightener. After some investigation, I found that their barrels were 0.020" too short. So I created these washers to fit...

Just a simple box with a lid to keep my telescope eyepieces safe.Fits  eyepieces size 1.25'' (approx 32 mm.)Printed mine in PLA, no need for support. 

based off pvs14 im tired gooeybye

Powerful Eyepiece

Left eyepiece focus bracket for vintage Zenith Binoculars. ... Eyepiece cover.

Celestron Telescope Eyepiece Lens Cover

Button shroud for the PVS14 nl914c battery housing, use thin double sided tape to install. ...I use 3M 300LSE

Cap for the Voigtlander 12mm Eyepiece.

Lens cap for telescope eyepiece holder

Extension tube for 1.25 telescope eyepiece

Ideal for 10mm eyepieces as well as 4mm eyepieces, this is truly exceptional.

Allows placement of a protective visor on eyepiece branches.

Dust cap for eyepiece of a set of Bushnell binoculars

A GoPro clamp on mount for a PVS14. Connects using standard GoPro mounting screws and nuts. It took quite a few iterations to get the mount and arm the right length and position. ...Fun little challenge though.

This is low profile adapter from T2(male) to 1.25" eyepiece holder. Lenght 15mm. ...I drilled 4mm hole for screw to tighten eyepiece in holder.

This is the enhanced Spider-Man visage. ...Files contained are: 1x Complete mask 1x Fragmented face plate 1x Left eyepiece assembly 1x Right eyepiece component

I modified the size of the eyepiece fittings to fit the wider eyepieces of a Zeiss Primo Star (approx 32 - 33 mm)

The Eyepiece of the Mechanist: A Singular Glimpse into the Realm of the Inventor

1.25 inch telescope eyepiece dust cover. ...Fits snugly (tested on Meade ETX-70) Category: Hobby

This is a 1 by 1 by 2 gridfinity holder for an eyepiece.

This collimation cap has a 0.20" opening and fits telescopes with a 1.25" eyepiece. ...

A cap to preserve telescope from dust when you remove eyepiece or guide camera.