pzkw 3 3d models

Pzkw zweiturmpanzer kv-II (russland)

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

this is 3

http://www.thingiverse.com/apps/customizer/run?thing_id=46335 Instructions Using the following options: Pencil_radius = 4 SD_gap = 2 Sign_TYPE = -1 Pencil_gap = 3 USB_gap = 4 Sign_TEXT = Braves Device_Order = 1 SD_cards = 8 MicroSD_gap = 3...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 3 font_thickness = 8 Font = write/orbitron.dxf stick_width = 8 hole_radius = 3 font_size = 10 flat_bottom = 2 message = ZVIKA

http://www.thingiverse.com/apps/customizer/run?thing_id=188481 Instructions Using the following options: ring = 10 adjust = 0 build_plate_selector = 0 layer = 0.3 seed = 3 trim = 0 clip = 2 build_plate_manual_y = 100 build_plate_manual_x = 100...

Customized version of http://www.thingiverse.com/thing:1728820 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1728820 Instructions Using the following options: number = 3

http://www.thingiverse.com/apps/customizer/run?thing_id=454702 Instructions Using the following options: nTwist = 1 allowed_overhang = .99 tol = 0.15 approximate_number_of_teeth_on_sun = 11 tubing_squish_ratio = 0.55 number_of_teeth_on_planets = 7...

http://www.thingiverse.com/apps/customizer/run?thing_id=351996 Instructions Using the following options: font = write/orbitron.dxf line_9 = line_8 = line_7 = line_6 = line_5 = line_4 = line_3 = line_2 = line_1 = #LaChef plate_thickness = 4 fontsize =...

http://www.thingiverse.com/apps/customizer/run?thing_id=27468 Instructions Using the following options: target_side = 50 Gear_Teeth = 10 freeArmStay_pos_l = [(freeArmStay_Offsetcos(30)),grip_offset-((freeArmStay_Offsetsin(30)))-arm_length,0]...

http://www.thingiverse.com/apps/customizer/run?thing_id=819457 Instructions Using the following options: B_Hinge = 14 L_Arm = 65 ant_holder = 1 ghosts = 0 H_leg = 3.2 R_Rotor = 9.7 L_leg = 0 H_HFase = 3.54 Wall_Rotor = 1.2 R_Screw = 1.53 Quadmic_R =...

http://www.thingiverse.com/apps/customizer/run?thing_id=6544 Instructions Using the following options: gear2_cut_circles = 5 gear1_setscrew_offset = 5 distance_between_axels = 24 gear2_bolt_hex_d = 15 gear2_shaft_d = 8.5 gear1_setscrew_d = 3.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=6544 Instructions Using the following options: gear2_setscrew_offset = 0 gear_h = 10 gear1_shaft_d = 5 gear2_cut_circles = 5 gear_shaft_h = 10 gear2_setscrew_d = 0 gear1_setscrew_offset = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: text_thickness = 4.2 border_width = 0 bar_style = bar_only bar_width = 55 font_size = 42 barextruder = extruder1 outline_thickness = 3.0...