qidi support 3d models

Qidi X-PLUS support to filament dryer EIBOS, after print I made some upgrades to improve the stability. ... You need supports only on the piece that connect to the printer filament support Printed with 4 walls and 15% infill

Qidi X-PLUS support to filament dryer EIBOS, after print I made some upgrades to improve the stability. ... You need supports only on the piece that connect to the printer filament support Printed with 4 walls and 15% infill

Therefore, I have created a Spoolbox Support for the X-Max and compatible QIDI printers. You can use this support while the strut is lowered or up in place. If you extend the strut, you can use a small block to keep the support horizontally. The...

I'm trying to harden up my Qidi Tech into a solid brick by redesigning the end supports to be sturdier and longer. These should fit snugly onto the 10mm rods with just a slight press. I'll need new screws for the lower stepper and mounting. Now I...

In an attempt to stiffen up my Qidi Tech into a complete brick, I recreated the end supports (shown sitting on the platen) to be beefier and longer. Should be sized to produce a slight press fit on the 10mm rods. Will require new screws for the lower...

<p>This is a remix of a model available on Thingiverse.</p><p><a href="https://www.thingiverse.com/thing:4869017">https://www.thingiverse.com/thing:4869017</a></p><p>The one on Thingiverse would not fit my cable so I made the cable hole...

This is a .stl i became from Qidi engineers to support the top cover of my X Plus 3, which was deformed due to shipping and permanetly scratching the ptfe tube while printing.Big thanks to great support from Qidi!I printed the 2 pices out of PC to...

feels like it could break if you accidentally drop the lid while putting it up so i decided to design some supports for it. now the lid feels much much sturdier while its in the up position. I included a file for some cushions (probably not really...

this is a support for bobine that are more than 1kg and with the original bracket didn't fit, for the qidi x-max

This action cam support is specifically designed for the QIDI X-MAX printer and tailored for use with the "cooau 4K" camera or similar models.\r\n\r\nPlease take careful note of your Action cam's size.\r\n\r\nIf you opt to use a different action...

Support to place the filament spool holder directly on the bracket. This results in less unwinding resistance of the filament spool when the entire filament spool holder can rotate instead of just the filament spool on the holder. ... The support is...

Qidi Tech 1 possibly X-Pro filament tube support/guide assembly.\r\n\r\nUPDATE 03/04/18: Added left and right versions of the tube guide arms featuring 2.5mm pilot holes, drill out after printing, install M3 set screws carefully to avoid squashing...

Qidi Tech 1 (possibly X-Pro as well) filament tube support/guide assembly. UPDATE 03/04/18 - added left and right versions of the tube guide arms that include 2.5mm pilot holes - drill out after printing and install M3 set screws. Be careful you...

With support spool you can't remove when the spool is finished. I have studied a "hinge" support spool. I have tested with 1kg and 750g spools. ... List of component: N° 5 bearing De=19 Di=10 B=5 mm N°2 parallel pin d4x12 mm N°3 screw TE M4x10 mm N°1...

This creation was crafted entirely within Tinkercad. ...Refine it live at https://www.tinkercad.com/things/gblklVPb5Oj.

If you're working with S3D, just add some manual supports to that shelf to ensure it prints correctly. Without those supports, the "shelf" tends to curl up a bit during printing. These remixed designs address this issue by adding support in various...

This is support for inner tube 8 mm of Qidi X-Plus printer.

This is support for inner tube 8 mm of Qidi X-Plus printer.

Support du scanner BEACON 3D normal Rev H pour la QIDI Xmax 3

This is supporto for inner tube of Qidi X-Plus printer. ...This part is for 6 mm tube (external diameter)

This is supporto for inner tube of Qidi X-Plus printer. ...This part is for 6 mm tube (external diameter)

These clips are to hold the ribbon cable for the Qidi X-Max on the outside of the frame so it’s easier to change when the time comes. I’ve had to change the cable twice and unscrewing the panels, the back and base to route it through became a bit of...

These clips are to hold the ribbon cable for the Qidi X-Max on the outside of the frame so it’s easier to change when the time comes. I’ve had to change the cable twice and unscrewing the panels, the back and base to route it through became a bit of...

I just recently converted my Qidi X-Plus over to a Lerdge K setup like my X-Pro. I wanted to keep the FFC ribbon cable setup but add the auto leveling functionality now available to me. I tinkered with several addon mounts but none of them seemed...

I added this pulley for reduce the resistance of spool. ...I used two bearings dimension D.19 d.10 x 5mm.

I added this pulley for reduce the resistance of spool. ... I used two bearings dimension D.19 d.10 x 5mm.

QiDi printer coil holder screw knob

If you don't currently have the carbon filter installed there is a template and instructions that are available through Qidi Tech support. It's not perfect and my need a little tweaking to work properly. I used m3 threaded inserts for attaching the...

They seemed a little thin and I couldn't slide the QIDI spool support rings over them either because it's a bigger than the aluminum tube diameter. I couldn't get my bearings to insert, they printed too small for the bearing OD. Here is what I...

I remixed this off a design qidi support sent me. I upgraded my qidi x-pro to the all metal hotend. I purchased the hotend direct from Qidi and they sent me some instructions to tweak. They sent me a version of this fan duct, saying the new hotend...