qidi tech software 3d models

Adapter for a 6mm ptfe tube to fit ontop the Qidi tech xmax/xplus/imates extruder cover.

Love My qidi Tech... still the best printer of the 3d printers I use. However after 2.5 yrs.. along comes a glitch.. contacting qidi left me on a path of discovery.. that apparently this could be quite a common problem with the 2017 models. Qidi...

This is a tool holder for the Qidi Tech I 3D printer. This tool holder could also be used on the Flashforge Creator Pro or any printer that has a gap between its frame and side panel. The tool holder clips onto the side panel and has slots for a...

This is a project for a QIDI Tech Build Platform. I will have a machine shop make these out of 1/4" thick aluminum. For this to work, you will also need to upgrade your linear guides for the z-axis which can be purchased here:...

3d printer Qidi X Maker not for 3d printing, but for architecting enclosures and test benches available in Solidworks file, STEP and STL file.

This adapter allows easy installation of any bolt on type feet or vibration dampers.Known compatibility with X-max and X-plus, but may also fit many other Qidi printers.Designed for M4 fittings, recommended feet are squash ball cup feet.All corners...

These are some feet I made for a QIDI Tech-1 Printer. ... I made them using Hatchbox TPU.

A simple spool holder spacer for a Qidi Tech 3d printer. This spacer can be placed between the body of the printer and the spool holder to extend it for wider rolls. Spacer printed in red ABS on a Qidi Tech 3d printer. Rafts and support materials...

... the holder. The magnetic portion goes under the bottom half of the hinge, and the shim goes under the top half to keep the cover flush. Works great in combination with my QIDI Tech I Magnetic Door Latch https://www.thingiverse.com/thing:4908773

... the holder. The magnetic portion goes under the bottom half of the hinge, and the shim goes under the top half to keep the cover flush. Works great in combination with my QIDI Tech I Magnetic Door Latch https://www.thingiverse.com/thing:4908773

My new Qidi Tech 1 wanted to fly because of the new design of her side and front panels that were impossible to keep closed so I decided to build a clip to keep them in place and avoid too much temp fluctuations. This is my first "Thing" and I'm a 3D...

Filament roll holder for the Qidi Tech X Max. The original telescopic tubes and the spool holder are reused. The PTFE tube at the filament inlet is inserted into the tube holder. ...The filament roll is now much higher, so it no longer breaks and can no...

The acrylic door on my Qidi Tech I (2018) printer developed a crack. I laser cut a replacement. The measurements aren't perfect, but it is not bad either. Use .100inch or 2.5mm acrylic. ... Follow your laser's normal settings for cutting acrylic.

It is specifically designed for the Qidi Tech 3D printer but it should work on the Flashforge also. Designed in Solidworks 2016. I've included the 3D model in Solidworks and IGES format. ...Print Settings Printer: Qidi Technology Rafts: No Supports:...

I only use the left extruder on my Flexion-equipped Qidi-Tech, so I removed the right extruder completely to reduce the weight being moved about, but without the right stepper motor there was nothing to hit the x-axis stop switch. So I made this...

I had found the Flashforge FFC Pro Vent Kit by ragingrivers http://www.thingiverse.com/thing:1708681; and decided to modify it to fit my Qidi Tech 1. Had to resize and edit the pieces that interlock with the hood. Included all the relevant files for...

In an attempt to stiffen up my Qidi Tech into a complete brick, I recreated the end supports (shown sitting on the platen) to be beefier and longer. Should be sized to produce a slight press fit on the 10mm rods. Will require new screws for the...

This design is a bracket for the QIDI Tech 1 printer with dual extruders. The bracket installs from the underside and is snap fit with no fasteners required. The LED strip is mounted and folded at the corners to get the 90deg turns. Super glue is...

The spool endcaps that come with the QIDI printer are ridiculously large and require that you unscrew them to swap filament. These give you a small 2mm lip to keep your spool from sliding off and allow you to get most spools on and off quickly. This...

Because I was not very satisfied with the standard spool-holder of the Qidi X-Max, I designed a new one, where the roll change is very easy. Additionally you need 2 round steel bars with 6mm diameter and 218mm length. Furthermore I recommend 4 ball...

Shim to print with glass on your QIDI printer. This should pressure fit your printer where your limit switch is. What you want is to place your glass and be able to print on it without the nozzles hitting it. You can print this shim (modify if...

Qidi Tech X-Max Bodwen holder

Remixed to fit the Qidi Tech 1

Fan Guard for Qidi Tech Dual Extruder. ...Fits over 2 40x40mm fans w/ 6mm gap in between.

This is a near identical replica of the extruder cover/filament tube holder for a QIDI Tech-1 printer. It may fit the Flashforge Creator (since QIDI pretty much copied that printer outright). Print face side down, no supports. ...

Portabobina per QIDI TECH per xmax realizzato con fusione 360 senza supporti PLA Riempimento 20% diametro interno 33 mm diametro esterno 73 mm

Qidi tech X Plus - top cover closing plate - with thermometer hole, with filament hole or just blank. ... As thermometer used Afriso 63826K - 0-60 grad

This a fan guard for the Qidi Tech 1 (2016) hot end fans. ...This is a friction fit so install does not require removing the screws.

A bracket to hold 5 PTFE tubes on the back of a Qidi Tech I printer. ...See http://www.abbas.org/drybox for more details.

... the Flash Forge Creative Pro). ...This would most likely work on pretty much any printer, considering that its attached by a single M4 bolt. Print Settings Printer: Qidi Tech Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 20%