qidi tech x max 3d models

The design files and instructions have been moved: Icarus - QIDI X-Max Carriage for Sherpa Mini R1 & Dragon / Mosquito Update November 24, 2021 New belt tensioner: The new Icarus belt tensioner for open belts has been tested now for a few weeks with...

On the X-Max you can have it installed all the time but I'm unsure of the other supported printer models.Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around 0.8-1.0 mm is good with a retraction...

Designed this 30mm fan shroud/adapter to concentrate the small fans cooling on the heat-pip e heatsink to help prevent heat creep on the high temp extruder. This fan mount replaces the two 9mm spacers on the 30mm cooling fan. Only additional...

Simple power cable support. My dogs while playing would sometimes pull the power cable out so I needed a quick fix. ... Needed is one very small cable tie.

Designed a trash container, that fits inside the printer. ...Print in two parts and glued together.For bottom 2 magnets 6x3mm can be used.Added a short and long version.

What do you need: Bondtech Dual-Gear Drive for 5mm Axis (DRIVEGEAR-KIT-175-5) 1x M3x25mm for clip axis + 2x washer (thickness ca. 0,6mm) - one under the screw-head one under the clamp. 2x M3x30 for cooling-block Also i would change the...

Created a custom cable restraint for my xmax to protect the hotbed cable. There are others out there, but my bed had thicker dimensions so I chose to create my own. This design requires 2 tie wraps to secure the cable to the retainer. Others...

IMPORTANT: This is a remix/update/improved version of the HERCULES carriage done by HumeBeam Changes/improvements compared to original "HERCULES" carriage: - Hotend cooling completely redesigned, tuned and optimized to utilize a 100% of the...

Small Thingi to cover the hole in the acrylic cover and still use the filament on top. ... Please rotate by 90° before printing so that the tube is touching the buildplate too.

Well, standard Extruder is not really running smoothly without a special fan duct as well as a ribbon cable holder. I designed a new riboon cable holder. ...Fanduct as well as vent clip from Humebeam.

a simple box to accommodate the hotend

Tested only with PLAPrinted with .4 nozzle, .2mm layer height, 2 walls and Arachne enabled.The following changes were made to the original design:Extended out the mounting hole for more room behind indicatorAdded fins to allow for repeated use...

2mm lower tool head for Triangle Labs K500 volcano heater.  This heats way better and allows way more flow.  I suggest using this specific 5015 fan the application.  I tried some other ones and they were not very good.  Use superglue to gasket the...

2 parts for easy printing Remixed from by mistertech Thingiverse: https://www.thingiverse.com/thing:3375047 by Jelliott526 Thingiverse: https://www.thingiverse.com/thing:4794054

This piece fits snugly at the entrance of the printer cover's upper portion. ...It should effectively resolve issues related to filament snagging, as well as enhance the process by which the filament is directed into the extruder, thus eliminating the...

Remix of Chad Wills' excellent Qidi X-Max, X-Plus BMG & V6 or Dragon carriage & top plate. This remix removes the plastic motor bracket and allows installation of an aluminium bracket made to common dimensions. Requires supports only below the...

Remix of Chad Wills' excellent Qidi X-Max, X-Plus BMG & V6 or Dragon carriage & top plate. This remix removes the plastic motor bracket and allows installation of an aluminium bracket made to common dimensions. Requires supports only below the...

My design for a tool-box for QIDI x-plus You can place the supplied tools ... and whatever else you like ;-) ... ...in this box that hangs off the side of the printer

This is a PTFE tube cutting jig for QIDI TECH I and X-one2 printers. Cuts standard 2mm ID X 4mm OD PTFE tube to the 32mm required length. ...

This is a PTFE tube cutting jig for QIDI TECH I and X-one2 printers. ... Cuts standard 2mm ID X 4mm OD PTFE tube to the 32mm required length.

... to mount my pi cam using this design (http://www.thingiverse.com/thing:1667505) and a 12-inch ribbon. Print Settings: Printer: Qidi Tech 1 Rafts: No Supports: No Resolution: 0.2 Infill: 25 Notes: Easy Print, estimated print time is about 1.5 hours.

Printer Settings: Printer: Qidi Tech 1 Rafts: No Supports: No Resolution: .2mm Infill: 20% Notes: I used the Qidi-supplied florescent orange PLA that came with my printer to get optimal results. ...Printed on the Qidi Tech 1 using Simplify3D on the...

The loudest component in the QiDi Tech 1 printer is its tiny 40mm x 10mm fan, situated inside allegedly cooling stepper motor driver modules. When you power up the printer, this fan dominates the sound scene whether printing or idle. ...After a year of...

Stand for holding Jayco or Sunlu filament dryer boxes on an Qidi tech X-Max printer. clips into printer stand that holds filament spools. ...

Qidi Tech Dual Extruder Fan Guard: A Must-Have Accessory That Fits Two 40x40mm Fans with a Precise 6mm Gap Between Them.

A custom mount is designed to secure five PTFE tubes behind a Qidi Tech I printer. ...For additional information, visit http://www.abbas.org/drybox.

Portabobina per QIDI TECH per xmax realizzato con fusione 360 senza supporti PLA Riempimento 20% diametro interno 33 mm diametro esterno 73 mm

This fan guard securely fits over the Qidi Tech 1 (2016) hot end fans, ensuring easy installation without needing to remove any screws.

... Tech printer, or any clone of the Flash Forge Creative Pro, which can be secured with a single M4 bolt. ...This setup is likely to work on most printers. Print Settings: Printer: Qidi Tech Rafts: Ignore Supports: Ignore Resolution: 0.2mm Infill: 20%