qidi tech xone 2 3d models
955799 3d models found related to qidi tech xone 2.thingiverse
E3D also sells them, here are a few options: Cheap chinese $2: https://www.aliexpress.com/item/32857007349.html? ... E3D, USA $16: https://www.matterhackers.com/store/l/e3d-type-k-thermocouple-cartridge/sk/MNXPV29Z E3D, EU:...
thingiverse
E3D also sells them, here are a few options: Cheap chinese $2: https://www.aliexpress.com/item/32857007349.html? E3D, USA $16: https://www.matterhackers.com/store/l/e3d-type-k-thermocouple-cartridge/sk/MNXPV29Z E3D, EU:...
cults3d
This is a replacement spool holder for the Qidi Tech Xone-2 that you can leave attached to the printer. It's much easier to use than the original holder which you have to unscrew every time you change filament. It's modeled after the spool holder...
thingiverse
This is a replacement spool holder for the Qidi Tech Xone-2 that you can leave attached to the printer. It's much easier to use than the original holder which you have to unscrew every time you change filament. It's modeled after the spool holder...
thingiverse
Side mount for the Mosaic Palette 2 and the Qidi Tech X-Max. This mount just fits in the open space at the side without the need for fixing with screws. The Palette stands up straight. I made 4 tubes at the bottom with numbers that directly feed to...
thingiverse
... in the filament And push it on up You got to guide in the filament And push it on up... ... This small funnel fits onto the end of the flexible filament guide tube on the Qidi X-One 2 and helps you insert it into the tube whilst not looking. ...
thingiverse
Adapter for a 6mm ptfe tube to fit ontop the Qidi tech xmax/xplus/imates extruder cover.
thingiverse
Love My qidi Tech... still the best printer of the 3d printers I use. However after 2.5 yrs.. along comes a glitch.. contacting qidi left me on a path of discovery.. that apparently this could be quite a common problem with the 2017 models. Qidi...
thingiverse
... the existing camera holder and then modeled a new mount and pivot connector that would place the camera in the front. I have it mounted on the left side of my QIDI TECH 1, but it should also fit just fine on the right side if you prefer. ...
thingiverse
This is a tool holder for the Qidi Tech I 3D printer. This tool holder could also be used on the Flashforge Creator Pro or any printer that has a gap between its frame and side panel. The tool holder clips onto the side panel and has slots for a...
thingiverse
This is a project for a QIDI Tech Build Platform. I will have a machine shop make these out of 1/4" thick aluminum. For this to work, you will also need to upgrade your linear guides for the z-axis which can be purchased here:...
thingiverse
3d printer Qidi X Maker not for 3d printing, but for architecting enclosures and test benches available in Solidworks file, STEP and STL file.
prusaprinters
This adapter allows easy installation of any bolt on type feet or vibration dampers.Known compatibility with X-max and X-plus, but may also fit many other Qidi printers.Designed for M4 fittings, recommended feet are squash ball cup feet.All corners...
thingiverse
A simple spool holder spacer for a Qidi Tech 3d printer. This spacer can be placed between the body of the printer and the spool holder to extend it for wider rolls. Spacer printed in red ABS on a Qidi Tech 3d printer. Rafts and support materials...
thingiverse
These are some feet I made for a QIDI Tech-1 Printer. ... I made them using Hatchbox TPU.
thingiverse
The acrylic door on my Qidi Tech I (2018) printer developed a crack. I laser cut a replacement. The measurements aren't perfect, but it is not bad either. Use .100inch or 2.5mm acrylic. ... Follow your laser's normal settings for cutting acrylic.
thingiverse
... the holder. The magnetic portion goes under the bottom half of the hinge, and the shim goes under the top half to keep the cover flush. Works great in combination with my QIDI Tech I Magnetic Door Latch https://www.thingiverse.com/thing:4908773
cults3d
... the holder. The magnetic portion goes under the bottom half of the hinge, and the shim goes under the top half to keep the cover flush. Works great in combination with my QIDI Tech I Magnetic Door Latch https://www.thingiverse.com/thing:4908773
thingiverse
My new Qidi Tech 1 wanted to fly because of the new design of her side and front panels that were impossible to keep closed so I decided to build a clip to keep them in place and avoid too much temp fluctuations. This is my first "Thing" and I'm a 3D...
thingiverse
Filament roll holder for the Qidi Tech X Max. The original telescopic tubes and the spool holder are reused. The PTFE tube at the filament inlet is inserted into the tube holder. ...The filament roll is now much higher, so it no longer breaks and can no...
thingiverse
It is specifically designed for the Qidi Tech 3D printer but it should work on the Flashforge also. Designed in Solidworks 2016. I've included the 3D model in Solidworks and IGES format. ...Print Settings Printer: Qidi Technology Rafts: No Supports:...
thingiverse
I only use the left extruder on my Flexion-equipped Qidi-Tech, so I removed the right extruder completely to reduce the weight being moved about, but without the right stepper motor there was nothing to hit the x-axis stop switch. So I made this...
thingiverse
In an attempt to stiffen up my Qidi Tech into a complete brick, I recreated the end supports (shown sitting on the platen) to be beefier and longer. Should be sized to produce a slight press fit on the 10mm rods. Will require new screws for the...
thingiverse
I had found the Flashforge FFC Pro Vent Kit by ragingrivers http://www.thingiverse.com/thing:1708681; and decided to modify it to fit my Qidi Tech 1. Had to resize and edit the pieces that interlock with the hood. Included all the relevant files for...
thingiverse
Because I was not very satisfied with the standard spool-holder of the Qidi X-Max, I designed a new one, where the roll change is very easy. Additionally you need 2 round steel bars with 6mm diameter and 218mm length. Furthermore I recommend 4 ball...
thingiverse
This design is a bracket for the QIDI Tech 1 printer with dual extruders. The bracket installs from the underside and is snap fit with no fasteners required. The LED strip is mounted and folded at the corners to get the 90deg turns. Super glue is...
thingiverse
The spool endcaps that come with the QIDI printer are ridiculously large and require that you unscrew them to swap filament. These give you a small 2mm lip to keep your spool from sliding off and allow you to get most spools on and off quickly. This...
thingiverse
Shim to print with glass on your QIDI printer. This should pressure fit your printer where your limit switch is. What you want is to place your glass and be able to print on it without the nozzles hitting it. You can print this shim (modify if...
myminifactory
Installation to cool the 2 filament enginesFan 44x44 plogue on the thread of the right infitantteurEasy to install with a can of selicon within small paws and below the bracket and your engines will have a longer life.