qrp radios 3d models
13984 3d models found related to qrp radios.thingiverse
A simple case for the shortwave pixie transceiver with a knob that fits over the potentiometer for easy frequency tuning. The PCB is held in by four 3x8mm bolts, although other screws may also fit. ...
pinshape
The SW-3B is a great QRP CW (5 watt Morse code) radio for amateur radio use. However, the knobs on the top could get damaged inside of a backpack or even a soft case. This cover is designed to protect the radio during transport while hiking or...
thingiverse
The SW-3B is a great QRP CW (5 watt Morse code) radio for amateur radio use. However, the knobs on the top could get damaged inside of a backpack or even a soft case. This cover is designed to protect the radio during transport while hiking or...
thingiverse
Because the overall package is lighter and smaller, it can be backpacked for portable (QRP) amateur radio operations. The antenna wire and feedline can be wound around the outside of the box for storage. Esun PLA+ was used (210 DegsC, 60 DegsC),...
thingiverse
QRP 30 watt 1:1 parts list: 1 type 43 toroid 25.4mmx15.5mmx6.35mm (Mouser part # 5943001301) 2 #8-32 stainless screws 2 #8-32 stainless nylon lock washers 2 #8 stainless split ring lock washers 2 #8-32 stainless nuts 2 spade terminals for internal...
thingiverse
I used stuff from my junkbox and redesigned the parts I used a readily available antenna rod from alxpress and a nut. Remixed from [see source]. It works. Printed in PETG For better results, of course you need to use a counterpoise. ... ...
thingiverse
Latest version of the remix of the original design. This time the antenna rod was bought from aliexpress and the nut is very common: https://www.aliexpress.com/item/1005002500129013.html?spm=a2g0o.order_list.0.0.12fa1802KfD3gW The nut holds...
thingiverse
Work in progress. I have used materials from my junk box. Antenna rod is from aliexpress 2.5m length. It works! ...Of course you will need a counterpoise for better results.
thingiverse
So I have a few QRP transceivers and I wanted to use some vertical telescopic portable antennas. The nature of the BNC makes it spin and the antenna can't hold vertically. So instead of spending a lot buying one, I designed this one to work...
thingiverse
This thing is a 3D-printed case for push-to-talk (PTT) microphone for QRP radio kits. In order to build this thing you will need to purchase: 1) an electret microphone element with a 10mm diameter an a 5mm length 2) a momentary-on limit switch...
thingiverse
Being a member (and membership Chairman) for the Flying Pigs QRP amateur radio club and knowing that a number of our members do have 3D printers, I decided to design a drink coaster with the Flying Pig logo on it for the members (and others) to print...
thingiverse
This is a small insulator for a field antenna for Amateur Radio. ... QRP is low power Amateur Radio. Print for private use but not for resale. ... Thanks and 73 de W2DAB
thingiverse
QRP Antenna insulator. ... Run cord through 3 hole section for quick adjustable tie off.
thingiverse
Antenna Insulator for QRP 11,5*2,5 cm, for dry weather, also as cable spoole Antennenisolator für QRP bei trockenem Wetter Der Antennendraht kann um den Isolator aufgewickelt werden. PLA ist nicht besonders UV beständig..für Daueraufbau anderes...
thingiverse
Holder for toroid and capacitor for build the end feed QRP antenna trap. The toroid is in front and the capacitor is in back. ... I used T50-6 toroid and SMD capacitor high voltage
cults3d
This is a shield for the QRP Labs 20W dummy load. I made 2 versions with or without M3 screws. Designed in OpenScad, sorce code are applied as always. ...Feel free to modify, Change the text, apply your own call sign if you want.
thingiverse
This is a shield for the QRP Labs 20W dummy load. I made 2 versions with or without M3 screws. Designed in OpenScad, sorce code are applied as always. ...Feel free to modify, Change the text, apply your own call sign if you want.
thingiverse
... narrow iambic paddle. ...I incorporated the paddle into a older DCxx QRP transceiver case. Printed with 35% infill using a Tevo Tarantula. ... The files can be edited here: https://www.tinkercad.com/things/jgFo98IQL5s-dc-40-and-keyer enjoy!
thingiverse
Just a simple, angled qrp transceiver stand. Made for my SWL DSW-40 and my SW-40 but should fit any around the same size. The top is about 4 1/4" x 4 1/4" with a 1/2" tall lip in the back. The angle is about 20 degrees. ...The legs have a wide base to...
thingiverse
Trying to make a free spinning spool for lightweight dipoles when i do portable qrp stuff. Idea is you just print 2x of file 1 and 3 and screw them together. Small goes into the center of of big. Should work with m3x20mm screws unless you mess...
thingiverse
QRP 20 watt 49:1 or 30 watt 9:1 parts list: 1 type 43 toroid 22.1mmx13.7mmx6.35mm (Mouser part # 5943001801) 2 #8-32 stainless screws 2 #8-32 stainless nylon lock washers 2 #8 stainless split ring lock washers 2 #8-32 stainless nuts 2 ring or spade...
prusaprinters
how to easy growing small plants and then repot without harming the plant?This is my anwser the QRP- Quick Recharge PlanterThe Support for 3 Planters is optional if u have another option to place your planters on. Manual:-Lay the Botton in the...
thingiverse
------------------------------------------------------------------------------------------------------------------------ My take on the QRP/travel mini magloop antenna. (small but roomy 45x75mm) The electrical design is not my invention just...