qs hub motor 3d models

Here is an outstanding and powerful hub-motor... ...one of the most powerful and yet affordable on the market...See the website for more...

An hub motor for smal electric vehicles, scooters, ebkes or mobility developed by Chinese Company QS

Quick model of a QS273. I used images from Alibaba for the dimensions. ...It's probably accurate within 2mm.Good for mock models for electric conversions.Long live Elon

A quite small (QS) motor for fischertechnik with a size of 30 x 30 x 20 mm and three-way plug connectors. Part list: * [DC motor 130](https://duckduckgo.com/?q=130+dc+motor&t=vivaldi&iax=images&ia=images), preferably in a 9V version, contacts...

QS Motor 3000W 205 50H V3TI E-Bike Spoke Hub Motor.http://www.cnqsmotor.com/en/article_read/QS%20Motor%203000W%20205%2050H%20V3TI%20E-Bike%20Spoke%20Hub%20Motor/976.html

This is for the QS motor not ZX which is below https://www.thingiverse.com/thing:5850143

3D design of Hub Motor

This is just a part drawing of overall view of hub motor.

Hub Motor

induction hub motor

This is the motor hub for a 16 x 16.

A small DIY bicycle hub motor downwind turbine

A hub adapter for a square axle hole and a circular motor axle!

a sleeve to stop slipping for my electric skateboard hub motor

An electric hub motor with threaded shaft on one side.The hub itself acts as a ratchet for freewheel.The model was created with Solid Edge.

A hub motor named Pablo.I intended to fabricate this motor, but, since the laminations were not off-the-shelf, it would have been very expensive.

Connects NXT motor hubs to Tetrix pieces with the help of some bolts and a lego axle Also check out my blog

Used on a FIRST Robotics window motor hub to hold a 1/2" thinwall aluminum tubing. Print 2. ...Top and Bottom.

The gears in the hub motor will eventually break. ...this is a replacement part because these gears are not sold any more.

The gears in the hub motor will eventually break. ...this is a replacement part because these gears are not sold any more.

... on their website. ...It's not completely accurate due to a lack of dimensions.The hub motors are mostly used in skateboards.http://www.michobby.com/product/hub-motor-for-electric-skateboards/Future additions will be- a separate shaft- easier to scale

This hub mounts on the littleBits motor with the D-shaped axle. I made this so my students can tape cardboard wheels or shapes to the motor. ...This is used in place of the motor mate which my students found a little harder to manage for some...

Designed this for an etrike project and needed a mount for the 6.5" hoverboard hub motor I was using. This was printed at 80% infill with 2mm sidewall and top/bottom, with petg printed with side down. This might be overkill and you might be able...

... hubmotor with a flattened axle. ...You can adjust the width of the axle matching your hub motor. DXF file is included for laser / water cutting out of stainless steel. ... Available washers are often cheap steel with mediocre surface protection.

Nubs to help the wheel slipping issue on Jacob's Hub motors. Just put them on and use some duct tape to hold them in place. ...The slot is there in case someone wants to glue them on with epoxy to give a larger surface area.

hub moor wheel based on cave rover

http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: hub_diameter = 15 axle_lenght = 10 axle_thickness = 3 build_plate_selector = 3 nuts_external_diameter = 7.7 nuts_across_flats = 7...

http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nut_height = 3.2 flange_height = 3 screw_diameter = 4 build_plate_manual_y = 190 build_plate_manual_x = 190 hub_diameter = 25 shell_thickness =...

http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nuts_across_flats = 5.5 flange_height = 4 axle_diameter = 2 axle_thickness = 2 nuts_external_diameter = 6 radial_holes_r_vector = 17...

http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nuts_external_diameter = 6 build_plate_selector = 3 shell_thickness = 1.2 axle_lenght = 12 finger_diameter = 22.2 layer_thickness = 0.2...