qu bd one up 3d models

Got my QU-BD One Up today missing this piece. Modified - re sized holes by +.2mm Center hole is now 18mm. ... Takes a little massaging, but would rather it be tight than too loose.

QU-BD One Up Extruder Parts For those who have broken or missing parts as I do, I am working on STL versions for all the Extruder pieces. Note that HEM_R4 is a modified part with all tab holes + .2 mm and the extruder head mounting hole at 18mm. ... ...

Y axis belt mount for Qu-BD One Up

Mounts for optical endstops originaly meant for QU-BD One-Up. For the time being X and Z axes only ... ...work in progress ;-)

I scaled this down to be small enough for a QU-BD One Up printer to handle. ...It seems to do the job just as well as the larger original.

Pulley for QU-BD One/ Two-Up Instructions 3d printable version of my pulley mod to reduce X axis carriage sag. Fishing line is to be used with this mod. You need to print 3 of the pulley wheels and two of the pulley's. Screws are to be used to secure...

A) Base plate for One-Up/Two-Up printers that was missing from original Kickstarter kits (basicHEM_r3.stl). B) Alternative for QU-BD's design of the Y-drive mechanism that adds some sturdiness, allows the belt guide to operate more smoothly. Replaces...

The stock extruder on the One/Two up has a bearing arm that is made of very thin MDF board and is one of the things that usually break first on this design. This is a replacement. The smaller holes/slot may need to be drilled out and clean up with...

Clips straight onto your one-up / two-up Y-Bed so the parts don't jerk around in your footage. I'm using a £5 Tecknet webcam I got from a charity shop and some free software on my PC to make the timelapses. Going to buy a fisheye lens so I can get...

If you are using Laird's extruder housing with the fan attached then you won't need an X adjuster arm - the fan frame itself lines up perfectly with the switch - so I did not include one. Using any other extruder might require creating something to...

Just a simple holder for loose filament up to about 50m comfortably, fits straight onto the existing design and allows easy insertion and removal of filament. Perfect if you are regularly changing colour! ...

This is a bearing retainer designed for the One & TwoUp! 3d printer kits to replace the weak melamine versions. These where printed in ABS with thick shells and 30% in-fill. More can be found on my web site http://www.DIY3DTech.com This thing...

This carries is a mash-up form thing 218670 and thing 224301, but with bowden setup. I recommend using Airtripper extruder for simplicity, but feel free to plug your favourite. Instructions 1x M5...

Also reduces the thickness, the original one was to thick so the belt was passing over one clamp hole. Updated 23/02/2014: made plates thinner to fit the printing plate. Updated 15/04/2014: got this changes since Feb... made shim and plate thinner...

HOWEVER, if you still would rather have that part from the start, I'll be happy to print them for you - please visit http://toybuilderlabs.com/qu-bd-one-up-z-bearing-alignment-spacer-special/ for details.InstructionsPrint two pieces for the One Up,...

HOWEVER, if you still would rather have that part from the start, I'll be happy to print them for you - please visit http://toybuilderlabs.com/qu-bd-one-up-z-bearing-alignment-spacer-special/ for details. Instructions Print two pieces for the One...

This design will allow you to mount a 40mm or 50mm fan to the side of the standard QU-BD One/Two Up extruder. ...The split design will direct air to both the extruder chamber as well as the peek barrel to prevent the filament from softening before...

Customized version of http://www.thingiverse.com/thing:220008 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=220008 Instructions Using the following options: ...

Bracket bolts to extruder body and directs airflow to the tip of the nozzle. To install this part you will need two 15mm M3 Bolts, two M3 Hex Nuts, a 10mm M2 Bolt, and a M2 Hex Nut. ... Attaches via the M2 bolt to an unused mounting hole in the...

Fan holder to cool down the stepper motor and barrel heat creep with one 40mm fan, like the one supplied by QU-BD. Can easily be removed for maintenance or filament changing. ... Works great with http://www.thingiverse.com/thing:408877 or...

One clip (Nut Holder V2) which holds the nut from the stock extruder from QU-BD, so you don't need to hold the nut while you're tightening the extruder clamp. This clip has M3 holes which docks onto a fan holder for the stock fan (or anything...

... ctc. p.p.s: Some people have asked me if I can put one together for them. The answer is basically yes, but I have a real job, so if you have patience and can wait for a few days, I will be glad to put one together for you. ...Send me a message.

This thing should be assemble together with Qu-bd Oneup / Twoup Bearing holder for extruder, and probably with some parts of the original holder. Instructions This thing should be used with...

I would recommend printing this as I have:http://www.thingiverse.com/thing:276192I can only verify this will fit on a Two-up, but I believe the spacing between the rod and screw are identical for the One-up, so there is no reason it should work with...

I would recommend printing this as I have: http://www.thingiverse.com/thing:276192 I can only verify this will fit on a Two-up, but I believe the spacing between the rod and screw are identical for the One-up, so there is no reason it should work...

Updated to include model for those with a one-up. Includes 2 unique pieces that should glue together nicely to form essentially the same thing! These nifty little brackets have a triple purpose! Kind of... They hold the mdf frame together if yours...

They hold the mdf frame together if yours has loosened up like mine hasThey cut the noise of the machine down by well over 50% if you have your printer on a surface that likes to resonate sound.It helps keep the printer in one place when it starts...

... thingiverse link for an image of how it should be setup. The base mount uses the same screws that go into the stepper, and the two top pieces use the same one that goes into the top of the rod (note you may have to buy longer screws for each part)

... thingiverse link for an image of how it should be setup. The base mount uses the same screws that go into the stepper, and the two top pieces use the same one that goes into the top of the rod (note you may have to buy longer screws for each part)

X-axis endstop mount spacer bracket to be used with MacAttak's X_Switch_and_ZAdjuster-_for_MacAttakextruder-_v1.stl mount and the original extruder. Instructions Reworked the...