quad 4 rods 3d models

this thing is a version of https://www.thingiverse.com/thing:3524150 for 25.4 mm structure tube I have added the same parts for linear guide of 8 mm with LM8LUU and 10 mm diameter linear guides, along with LM10LUU bearings

QUAD 4-WHEEL SPORTS

The body of this quad-copter was made by myself and the parts that on attach to it is supplied by my tech design teacher.

mini chasis para motor 1806 y helices 4"

BUILD PIC UPDATE: Carbon rod / 3D printed 176g 200mm Quad 3rd Quad build ever....tried to make this one as lite as I could get it... carbon rod arms...way tuff 3D printed parts, very lite Cut down 9X8c v2 RX...custom 31mm antenna micro buzz bar...

Remixed my small carbon rod quad....for FPV... added LED up front so on board battery warning could be seen as a glow LH corner of FPV view....FPV plate can be moved foward or back, I have mine adjusted so to just see front of quad for ref... ...80g...

This product can allow you to carry all your rods to the boat in one trip from the truck

This design was especially tailored for motorcycle riders while effectively resolving the most common and annoying problems with commercially available mounts ###Problem: - The Ram mount grip X is not very reliable and it's easy to lose your phone...

http://www.thingiverse.com/apps/customizer/run?thing_id=1341482 Instructions Using the following options: lidheight = 6 sectionsh = 14 sectionsw = 1 sectionsl = 1 width = 37.2 lidthickness = 1.2 length = 37.2 cornerrad = 5 tol = 0.4 height = 17...

These are for extending a 3/4 inch rack shelf rods. E.g. for adding a tiny bit more height to a rack shelf. Or, the existing rack shelf is too a bit too high and you want a shorter rod to make the rack shelf fit. ... The threading for my rods worked...

This is a battery pack for 4 18650 Batteries. ... This is designed for use on fishing rods requiring battery assistance. Very easy to print without support. ...

rods tightening

Made for homebrewing a quad beam antenna. ...Mounts on 1" pvc and fits 6mm fiberglass rods used for driveway markers found at big box hardware stores. ...

This is a model that I created from a website by IW5EDI (http://www.iw5edi.com/ham-radio/2587/2-4-ghz-cubical-quad-antenna) that is a 4-element cubical quad (1 radiator (driven element), 1 reflector, and 2 directors). ...The coax is not shown and can be...

A detailed Quad copter 4" body designed to be used with 1/4 inch dowels for boom arms You will also need to download the deck base to hold your electronics.

This is a model from a website called Marty Bugs (https://martybugs.net/wireless/biquad/) that show the assembly of a low cost 2.4 GHz Bi-Quad antenna.

Then to mount to the quad, I used 3M extreme mounting tap and some foam as well as two zip ties to make sure it doesn't fall off in crashes. ...The tolerances are very tight so you might want to expand the model very slightly in your slicer but printing...

This is an experimental 2.4ghz quad helix antenna I started building but eventuall gave up on. As I don't know enough about antennas and impedance to make the proper copper vanes, and it being near impossible to solder on anyway, I didn't continue...

quad???

My own take on the H&K 416 CQB style, This is a remix from another user. ... All i have done with this file is shorten the handguard from 8" (inches) to ~4" (inches) to suit a custom 416 CQB build.

1806 brushless with 4" props (30.5 x 30.5 stack) Racerstar 4 in 1 ESC https://www.banggood.com/Anniversary-Special-Edition-Racerstar-REV35-35A-BLheli_S-3-6S-4-In-1-ESC-Built-in-Current-Sensor-p-1180734.html?rmmds=myorder&cur_warehouse=USA CC3D with...

Units: mm No viruses Formats in the archive: MAX2014 OBJ FBX Polys: less then 3.800 Verts: less then 4.500 Model created with 3ds Max 2014 Native Max file setup with V-Ray renderer and V-Ray materials Preview rendering made with V-Ray The lighting...

Units: mm No viruses Formats in the archive: MAX2014 OBJ FBX Polys: less then 3.500 Verts: less then 4.100 Model created with 3ds Max 2014 Native Max file setup with V-Ray renderer and V-Ray materials Preview rendering made with V-Ray The lighting...

quad projects

A quad modeled from a 450 YFZ quad

Quad model for surveillance and rescue.

SummaryMy first quad creation on my Hephestos Prusa i3 I used 4 bumpers in Filaflex to reduce vibrations on motors. Motor to motor : 30.5cm It's a work in progress. I wanted to reduce screws I have to build the landing gear Materials : PLA...

... as long as I have access to a laser cutter I can replicate parts quickly. Overall it’s a much nicer platform that manufactured frames as it’s far cheaper and quicker to get parts. The arms are 10mm stock and seems stronger than normal 250 quad arms.

1) Lock Nut 2) 608zz bearing (8mm x 22mm x 7mm) 3) Printed V-slot threaded rod bearing (screw this into the top of the V-Slot) 4) Printed Horizontal V-bar End 5) A regular nut (should fit into nut slot on the printed V-slot V-Bar) 6) 628zz bearing...

DESCRIPTION These are wall-mounted brackets to make disc shelves in combination with 3/4" dowels or similar rods. They are large enough to fit large-diameter midranges (180g class), all drivers and, putters. <h2>PRINT SETTINGS/FILAMENT</h2> ...