quad antenna 3d models
68146 3d models found related to quad antenna.thingiverse
Quad pigtail antenna mount. ... Designed for 5mm standoff Printed in PLA and it's actually on my quad :)
thingiverse
** This Quad antenna spreader can be used as a basis for antenna design on 6m, 2m, 70cm, etc.. I wouldn't use it for an HF antenna design as the spreader isn't robust enough.** ** With all that being said, you MAY be able to use it on 10m but I...
thingiverse
Antenna guard for my "Sandwich" quad Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: Yes
thingiverse
A buddy of mine needed an antenna mount for his quad copter and wanted the antenna tube piece slightly raised so the wires could slip in without being pinched - here's what I came up with...
thingiverse
To hold plastic tubes which houses the antenna on the sides of the mini quad with minimal hardware. ... Instructions .2 layers with 20 percent infills.
grabcad
This is a model from a website called Marty Bugs (https://martybugs.net/wireless/biquad/) that show the assembly of a low cost 2.4 GHz Bi-Quad antenna.
thingiverse
Angled antenna tube mount for mini quads. ... Requires short length of 3mm antenna tube.
thingiverse
This is an antenna mast/mount for 1-2 Antenna Receivers for the QAV105 Micro Quadcopter
thingiverse
Quad parabolic antenna model prepared to install 4 sensors in the focus point. First programed in OpenSCAD, creating supports in SketchUp and finally scaled in the Meshmixer. Printed in PLA just to prove the design. ... Print settings can be seen...
pinshape
Have a great day. ...:-) Created with Design Spark Mechanical http://www.rs-online.com/designspark/electronics/eng/page/mechanical
thingiverse
Have a great day. ...:-) Created with Design Spark Mechanical http://www.rs-online.com/designspark/electronics/eng/page/mechanical
thingiverse
Needed a case for my 5.8ghz Bi-Quad i hobbled together. ...Works Great , need to make a template for it, Was ripped from some Hubsan FPV Controller but should work with many different patch style antennas.
thingiverse
The battery on my quad was sitting right on two bolts on my 210mm frame. I didn't want it to puncture the battery in case of a crash so I made a spacer for the battery. I also designed an integrated antenna holder. ...It is at 50 degrees to make it...
thingiverse
This is an antenna mount for the ImpulseRC Reverb. ...It's supposed to work with the "Antennenfreund" MMCX Double Quad Antenna.
thingiverse
Antenna holder for any V2 frame with GoPro Mount. Antennas are 90 degrees from each other and 45 degrees back. ... Print Settings Printer Brand: MakerBot ...
thingiverse
These are a collection of various antenna mounts that I've created for the following quads: Misfit 210 (Pats Mini-H) Lumenier QAV-R (Raceblade) Shendrones Tweaker Xhover Element Some of the quads use larger hex style standoffs, and others use the...
cults3d
I made this as a weekend project, dimensions are from a website http://www.csgnetwork.com/antennae5q2calc.html you just need to enter the frequency and hit the calc button, I have included a screen grab of 446mhz. I used 12 AWG copper wire to form...
grabcad
I recommend chemical etching for elements and the radiator due to the small scale and for accuracy, but machining may be possible.I came across this antenna that looks suspiciously like a copy of the wimo antenna...
prusaprinters
Mini race quad 210 frame antenna mount Category: R/C Vehicles
thingiverse
Made for 2 mm tube (inside) or 4mm (outside). ...Even a 3mm heat shrink will fit because off the cutout. You can use heat shrinks or some rc antenna tube.
thingiverse
This is a GPS and antenna mount for the GX140 3inch FPV drone frame which is sold under various brands on Chinese commerce sites. Bottom plate/arms is 4mm. ...The GPS mount accepts BN-180 size GPSs.
grabcad
This is a model of a scaled down version of the 8-Director element (1 reflector and 1 Radiator (Driver) elements) X-Quad from Wimo (https://www.wimo.com/xquad-antennas_e.html) designed to operate on the 2.4 ~ 2.5 GHz ISM band. It can be custom tuned...
grabcad
This is a model of a scaled down version of the 8-Director element (1 reflector and 1 Radiator (Driver) elements) X-Quad from Wimo (https://www.wimo.com/xquad-antennas_e.html) designed to operate on the 2.4 ~ 2.5 GHz ISM band. It can be custom tuned...
thingiverse
This is for Toad 90 Micro Quad frame. ...Print it on TPU.
thingiverse
I made up a minimalist antenna mount for one of my blackouts to keep the stock look. Replaces the 2 front flight controller posts. ...Sized to fit my FRsky D4R-ii
thingiverse
#### Quadcopter Rx antenna mount for receivers mounted below the top plate The antenna guides are tilted back to make the screw holes easily accessible. A compromise of 35° tilt to the sides had to be made (instead of the desirable 45°). The thing...