quad arm 3d models
125389 3d models found related to quad arm.
thingiverse
This is a remixed arm to add a fillet because I kept having the arm snap at the exact same location (right next to the motor) upon crashing. ...Hoping this adds enough strength to be helpful.
thingiverse
A remix of the F450 quad arm by villamany Redesigned the arm to not need supports due to the overhangs in the design.
thingiverse
I had to make a small tweak to where the extensions attached to my quad arms. After this, they fit perfectly! ...Great work!
thingiverse
500 size Quad arm, they meet dt750 motors, also they meet SK450 landing skids ive made before enjoy!
pinshape
SummaryI needed a solid version of tosjduenfs' quad arm so that there was room to lay the fiberglass filament. I also printed a PLA version so I can perform deflection and failure tests to compare the two prints. tosjduenfs: 7g PLA: 9g...
thingiverse
I needed a solid version of tosjduenfs' quad arm so that there was room to lay the fiberglass filament. I also printed a PLA version so I can perform deflection and failure tests to compare the two prints. tosjduenfs: 7g PLA: 9g fiberglass/nylon:...
thingiverse
Remixed (redesigned) arm for the "250 Quad" design (https://www.thingiverse.com/thing:855416) which is thicker and more robust.
thingiverse
A better quadcopter arm with mounting holes and sleeker design. ... Instructions Designed in Sketchup 2013
thingiverse
Longer arm version for the Mini Flame Wheel Style Quadcopter frame by tosjduenfs to accommodate 9 inch diameter rotors. Instructions First Layer 0.4mm, rest 0.2mm. PLA, extruder temp 185 C, bed temp...
thingiverse
This is an arm for a Nighthawk board with a spacing of 223mm Print Settings Printer: Frankenbot Rafts: No Supports: No Infill: 75% Notes: 25mm/s speed and printed with PLA you can print it with less infill however it will flex more but will break...
thingiverse
X-Quad made from ZMR250 arms you have to drill the third hole into the arms ;-)
prusaprinters
X-Quad made from ZMR250 arms you have to drill the third hole into the arms ;-) Category: R/C Vehicles
thingiverse
... doesnt have holes for motors with 16/19 spacing but the one in the picture i drilled my own. And yeah i could have made a better looking section where the fasteners and the arm meets but i am making/drawing my own 250Quad so just changed abit :)
thingiverse
Dia engine bolts (M3): 16-17.5mm CC mounting bolts (M3): 13.5mm Clearance hole for engine axis: Dia 8mm Tilt angle: 9 degrees I use it for a 280 racer with 5" propps.
thingiverse
Right and Left versions of Quad arm with leg attachments and thicker motor mount
thingiverse
New design of the arm for using famous HobbyKing's DT-750 motors whit this amazing quad. Designed in SketchUp. Source file available for download. Test flights are in progress. I will update with results. 4-Aug-2014 (v1.0) -Enlarged 0,5mm the place...
thingiverse
To mount the usual Turnigy LED's onto your quad arms. They are designed for 3mm arms so that when you glue them on, the sit flush with the bottom of the arm. Will of course be even better on thicker arms, designed to protect them just incase you rub...
thingiverse
Not tested, should fit a 200x200 bed diagonally. ...Mounting patterns have not been affected.
thingiverse
this is a stator fin, also called a stator vein in a jet engine, it it designed to move the air around the arm efficiently. in theory it should be more powerfull and quieter. ... Print Settings Rafts: No ...
thingiverse
Here are some arms I made for the 230 and 250 boks quads. I made it so you can still use the vibration dampening system. It is far stronger than the original (pretty hard to bend). Although it isn't a light part (13g), it is still lighter than the...
thingiverse
Perfect for Soft Mount, Protect all sides... ...
thingiverse
Testing a new arm design for EflyerSteve's mix of the Cloneout Mini H Quad arm fromhttp://www.thingiverse.com/thing:347202 v2 : Updated with uniform channel spacing Works with Hammer 2.0 Mini Quad as well.
thingiverse
But with this Top-Plate, with enough Thickness, each arms are now supporting each other. Which makes this structure more Sturdy. Also, it is not pleasant to look at Bare-bone 4 Carbon-Fiber Arms Not meeting together at the center nicely. I printed...
thingiverse
Whipped up some Capacitor mounts for my Nasty 10" FPV quad. They also guard the motor wires. There's plenty of room between the prop and Caps if you're running Aeronaut Cam carbon. It's a little closer with MAS props. Running a little wire to the...