quadcopter case 3d models
210686 3d models found related to quadcopter case.thingiverse
I needed a case for my little Blade Inductrix Quadcopter, so I made one with SketchUp. The lid fits nice and tight and the Inductrix fits in there good, and dose not rattle around at all. I hope you like it.. ...Print Settings Printer Brand: ...
thingiverse
Carry case for 80mm micro quadcopter. Was designed for the speck 80 by Rotorious FPV but should also fit the Eachine Tiny QX80. It has a small inner compartment for spare props and 5mm pegs that fit into the bottom of the frame. ...Print Settings Rafts:...
thingiverse
This is a case, case lid, and controller mount for a LiteHawk. Other micro-copters may work as well. Glue the controller mount to the Lid top for an all contained storage solution. Recommend filament calibration prior to print. ... Print Settings...
thingiverse
I included the assembly as an .iges in case someone wants to modify the surface model. Also this is in INCHES so scale it by 25.4 to get millimeters. The metric files were too large to upload. ...Print Settings Printer Brand: ...
thingiverse
3d Printed case to fit the micro 105 FPV Quadcopter from Punkkills
thingiverse
i made a 105 micro fpv quadcopter from punkkills and needed a case for carrying around. ... i made a specific case for punkkills quad and five 1s 500mAh 25C LiPo from Eachine Edit: i added a second version of the bottom part for larger lipos
thingiverse
carry case with top for a cheerson cx-10 quad, the smallest in the world. ...Its a little tight, but it works great, but improvements/fixes may be on the way.
thingiverse
Eachine Fpv Quadcopter Case Tarot 250 Very Thin I made this for my tarot 250. ...-Angle is adjustable -pug is in the back -Very very thin
thingiverse
May put 4x2 4s750mAh batteries inside. ... Need to drill small hole for antenna if it extends beyond the case. ...
thingiverse
So for the modification I had to cut the inside curves to make it more square, I also chopped the top of the case down to just above the batteries to make it much shorter and less printer time. It took just over 14 hours to print both parts. ...I also...
thingiverse
I really liked this design and needed a case for my BetaFPV75 and batteries and USB chargers. This modified is to fit the BetaFPV75X, which the main difference is from my previous modification for the 2S batteries. Which are a little taller and have...
thingiverse
Yes i sleeved my cables with paracord (used for case modding) You finde sleeving tutorials on youtube ;) Instructions The space for the PCB is 32 x 38 mm. So the PCB should be a bit smaller to fit in. I used tape on a plane copper pcb to protect...
prusaprinters
I really like the design of the printable Peon230 Quadcopter by Tech2C. I did a very simple powerboard for my quad (cut pcb > tape parts that have to stay > etch > solder) and needed a case. Maybe its usefull for one of you ;) I have my...
thingiverse
Backpack Plug Bundle Mount/Hang buckle Strap for FPV Drones Quadcopter Case Bag
thingiverse
Customized version of http://www.thingiverse.com/thing:58001 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58001
thingiverse
Case for the New Proto X Nano quadcopter since it didn't come with one. Put it in this case and toss it in your bag keeping your blades safe from breaking. Take it with you everywhere!http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXDVYH I...
cgtrader
Case for the New Proto X Nano quadcopter since it didn't come with one. Put it in this case and toss it in your bag keeping your blades safe from breaking. Take it with you everywhere! http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXDVYH I...
thingiverse
A case with open top for GPS antenna CJMCU APM2.6 Instructions I mount this on a 4mm carbon fibre tube, but you can use a bigger diameter by simply drilling the hole for the tube.
thingiverse
Raspberry PI case for Quadcopter. ... Additional space is designed to fit the receiver on the side of the case.
thingiverse
This is a simple cover (case) for the F450 or Q450 frame DIY quadcopter. It is 6 cm high so there is enough space for circuits. It has holes to fasten it to the frame with wires. The PLA used is silky silver, completed with two pieces of black...
thingiverse
I don't have a cased VA1100, so please let me know which one works best for you! https://tinkercad.com/things/6qjNWDce3kP Instructions Insert the prongs into the front rounded hole of your Phoenix...
thingiverse
Case for power distribution board. ...Now the power distribution board can be mounted on the underside of the ZMR250 frame reducing the risk of short circuits of the main lipo power.
thingiverse
Added a plate to HLMAX's telemetry Radio Case for mounting on the side of the T4 Quadcopter by Brendan22. ... The plate has pegs that fit the side slots of the T4 Instructions Print with supports and...
thingiverse
Remix of existing design, modified to fit a hero 3 an added an angle to it. attaches to quad with 3mm cable ties. ...layerlens is used to hold the gopro in the frame.