quadcopter esc 3d models
12961 3d models found related to quadcopter esc.
thingiverse
Instructions Print :-) Solder ESC's to energy distributor Mount the energy distributor using the inner mounts (dim. 30.5 mm) Mount ESC's by using zipties. If you are using an ESC that provides a USB interface (as in our casse) make sure that the USB...
thingiverse
Universal Quadcopter ESC Guards with 4mm Arms
thingiverse
This is an ESC cover I've designed to fit the BumpBee ESC. It measures 30mmx15mmx4.5mm inside the shell. Resize to fit others. ... Preferrably print in flexible TPU material with a 50%+ infill.
thingiverse
... frame of the drone and then into the 'Standoff Screw Mount'. The ESC then mounts through the posts in which the female side of the 'Standoff Male Female' file press fits onto. ...Another set can be added on top for the FC and additionally the VTX.
thingiverse
increased the inside diameter of the square hole for 15mm rods.
thingiverse
For those that have the Bumblebee Quadcopter kits, this is a motor/esc mount that I redesigned to be stronger and less prone to snapping. Also added a better channel for the cables and a zip-tie groove to ensure proper mounting of the ESC. Using RCM...
grabcad
Model in Solidworks 2016. ...STEP, IGES and STL Available.More infos about the part:http://bit.ly/1FJ1vZv
thingiverse
I've put my Rctimer 5010-620KV motors on this arm.http://rctimer.com/product-911.html Tinker this at TinkerCAD:https://www.tinkercad.com/things/eeyW3mPFbS7-t4-quadcopter-arm-esc Instructions I printed this with ABS .2 25% Fill with supports using...
thingiverse
Look stylish while protecting your ESCs with these Shark Fin style ESC covers! See image for dimensions. ...Feel free to remix!
thingiverse
Check it out: http://www.3dhubs.com/harrisburg/hubs/mark And checkout the complete series of BackyardRC's Quadcopter parts on Thingiverse: Center Hub: http://www.thingiverse.com/thing:136209 ESC Mount: http://www.thingiverse.com/thing:122363 Motor...
thingiverse
basically this is the same frame but i made room for bigger escs as in the original frame my escs would be clipped by the props. i've deppend the slits where the escs go witch makes the frame even more fragile if you print in pla. ...
thingiverse
Designed to mount two Bullet 30A ESCs at an angle with a center wire pass through. Mounting rails on bottom fit slots in a Neato Dallas frame. ... Attach ESCs with servo tape and use top cover to hide the gap.
thingiverse
Canopy and ESC protectors for the Usmile UX5 quadcopter. It allows for rear facing power connector and top mounted VTX. The FPV mount is designed for the original RunCam Swift. ...It uses two of the 35mm standoffs provided in the UX5 kit.
cgtrader
For those that have the Bumblebee Quadcopter kits, this is a motor/esc mount that I redesigned to be stronger and less prone to snapping. Also added a better channel for the cables and a zip-tie groove to ensure proper mounting of the ESC. Using RCM...
youmagine
I have started to build myself a quadcopter and part of the build has been to mount the speed controller (ESC) to the frame. The controller has for ESC's built in but no mounting points to attach it to the frame. ...Using the existing mount points on...
grabcad
keeps the Bulltec 30A ESC in position on the Frame (f450 Flame wheel).
thingiverse
This is a an ESC Cover (Designed around a Spedix ES25 25A/35A Speed Controller for Multi Rotor Aircraft), that also is a mount of Lumenier's Programmable 4 LED Boards. When printed with the mentioned settings and filament, weighed 3.2 grams. ...
thingiverse
based on thing:46655. I tried printing the original cable clips but my printer doesn't like thin walled small objects. So I redesigned it to have a little bit more meat and now I can print them just fine. If you print this, please click the "I made...
thingiverse
The quadcopter depicted in the images was constructed from the following parts: CLRacing F7 Flight Controller Holybro Tekko 32 4-in-1 ESC FrSky R-XSR Receiver Tramp HV Video Transmitter Foxeer Predator Mini V3 FPV Camera, 2.5mm Lens EMAX RS2306...
thingiverse
Micro quadcopter frame for 1103 motors, 16x16 mm FC&ESC, Eachine TX01-02-03 camera&VTX, 30 mm battery width
thingiverse
The Quadcopter ESC can be 20mm x 30mm x 15mm. ... With notches for the cable ties.
thingiverse
My take on quadcopter ESC protection. ... Will recommend printing with flexible, but probably will work with PLA / ABS/ etc
thingiverse
Simple guard to help protect your quadcopter esc in the event of a prop strike. Used on my 250 size racing quad. ... The cutout sits on top of the esc and the side part faces the incoming prop blades.
grabcad
Electronic speed controller for quadcopter. ...4 esc and ubec fitted into 1 box.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1175570 Instructions Using the following options: Text_Size = 1.4 Width = 20 Thickness = 4 Length = 64 Line2 = Clermont Line1 = ESC
thingiverse
... vented one. ...I wanted to make this as I'm using a plane ESC instead of the suggested quadcopter ESC, which is a tighter fit, so I wanted to force some air in to cool it. ...It weighs about 3g compared to the original Carbon Fibre which is around 2g.