quanum 3d models
507 3d models found related to quanum.thingiverse
Валялись очки Quanum долго из за того что просто неудобно было ими пользоваться!(провода,аккумулятор приемник все болталось ) А теперь все удобно и можно летать. :) Перечень деталей : Приемник boscam FPV 5.8 8ch , https://goo.gl/w05lS8 8 pin 4...
thingiverse
A fastener for the quanum goggle Print Settings Printer Brand: RepRap Printer: mendel90 Rafts: No Supports: No Resolution: 0.2
grabcad
Carbon Fibre frame of the Quanum XJ470. Carbon parts are drawn from flat bed scanner files.Metal parts measured with Vernier Callipers. Thus there are some discrepancies. ...+/- 1mmTop plate has been modified too.
thingiverse
Fatshark Quanum Battery Holder Simply case for mount Quanum Battery on FatShark Strap. ... Layer Height = 0.2 mm Infill = 20% - 40% Material = PLA Plate Adhesion = None Support = None
thingiverse
Holds HMDVR so that it fits in the large side pocket on the Quanum V2 goggles.
thingiverse
Wall Mount for Hobbyking Quanum FPV goggles. ...Print with the long side on the bed.
thingiverse
This is a standoff for the Quanum Trifecta Lid. ... Handy if your flip32 / naze32 has straight pins.
thingiverse
Battery enclosure for the Quanum Trifecta tricopter. ...I designed this to proved protection from crashes and to keep the battery secure during flight
thingiverse
The dumb lens in my Quanum V2 Pro goggles always slid around and I was constantly adjusting it when really I just wanted the lens as close to my face as possible. Replaces foam inserts and holds lens in Quanum V2 at either extent depending how...
thingiverse
... Venture FPV Quad. ...The "mini gps mount" was designed for a 28mm module. The normal "gps mount" has an integrated 4mm mounting rod. Both versions fit into the hood of the quanum venture, as displayed on cover photo - glue/screws are not required.
thingiverse
Adaptador para poder pegar con cinta de doble cara cualquier receptor en el frontal de las gafas fpv de quanum Imprimir al 100% para darle solidez a las patillas
thingiverse
Simple Slip in flat mount for the Crazepony 700tvl fpv camera. ...Mount was then hot glued to Quanum v2 monitor. ... Camera dimensions 12.5mm x 12.5mm x 6mm
thingiverse
Tighten or remove props from Quanum MT1806 motors without bending the prop. ...Print Settings Printer: K8200 Rafts: ...
thingiverse
Lensegrab is a simple holder for a lense from a Quanum V2 to fit into a v1. ...Print Settings Printer Brand: RepRap Printer: ...
prusaprinters
The dumb lens in my Quanum V2 Pro goggles always slid around and I was constantly adjusting it when really I just wanted the lens as close to my face as possible. Replaces foam inserts and holds lens in Quanum V2 at either extent depending how...
grabcad
Based on the Quanum Nova electronics , i made this drone , it fly well.All structure elements are 3D printed , the tubes comes from carbon arrow (7mm diameter) , it's very strong and light.The battery size here is a 3S 4amp , the Quanum Nova main...
thingiverse
Modded my Quanum FPV into an Cardboard like VR Goggle. I used lenses from Binocular, still at work to get a right picture.... ...Print Settings Printer Brand: RepRap ...
thingiverse
A Propellor nut knob for the Quanum nova. May work with other prop nuts. The diameter is set to 14mm. Should work great! Enjoy! ...Here is a screenshot of Objecthttps://gyazo.com/6dd2e4699fa1438876215e85e4cb38e9 Print Settings Rafts: ...
thingiverse
This is a hand held fpv screen adapter for the Quanum v2 monitor. Its a nice tight fit. This will also hold the FR632 Diversity Wireless AV Receiver, Battery strap as well as a XT60 battery connector. ...Its great for testing on the work bench and on...
pinshape
This is a simple and protective pod built for the Quanum DIY FPV kit V1 from hobbyking, With some velcro on the back of the camera it fits very snugly. the VTX is QR zip-tied upright only because I have no 90 bent antenna. ... Printed with ABS,...
thingiverse
I designed this to make an extra extension for the monitor on the Hobbyking QUANUM V2 goggles. People have complained (including myself) that the Fresnel lenses included with the kit are not powerful enough and causes focusing issues. ...This extension...
thingiverse
I wanted to put my Quanum Pico board, so that I can switch it easily between micro quads (for example : http://www.thingiverse.com/thing:1250550). So I designed a small box and hot glued the PCB on it. I fix the box to the frame with rubber bands.
thingiverse
Quanum XJ470 Cover Plate like the original one. There is a semi hole in the middle to see Pixhawk status led if printed with clear PLA. The last few lawyers can be printed in other color. In the front part there is an slot to fit 3DR radios (or...