quip floss 3d models

Multiple Variations of Camera Angles Available Four distinct camera angle options are now available, designed specifically for use with the Foxeer Predator Micro and Runcam Racer 2 cameras. These angles include 40 degrees, 45 degrees, 50 degrees, and...

THIS MODEL IS DEDICATED TO MY DEAR FRIEND SANTA FLOSS3DSMAX DWG C4D STL OBJ

This device was constructed with precision and care utilizing the innovative platform of Tinkercad. ...For easy access, editing can be completed directly within the browser at this URL: https://www.tinkercad.com/things/dH9PmP1G5xj

Simple Fit for your Flux 3.0 frame

This is a Fin.

Do you often find yourself turning your head upside down? Don't worry, Turtlemode and this Fin will come to the rescue - unless you're stuck in thick grass! The design has been made hollow to minimize weight and enable further development (airholes...

Embellishment thread keeper. Matches Hexdoll's decorative yarn spool design found on Thingiverse at ID #859506. ...Accommodates up to 30 spools, leaving ample room for winding an entire skein of thread without obstruction.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I have no idea why you should create a stack of toothpicks... ...But I wanna publish it

<p>I printed the original winder and it works great, but I was not a huge fan of the hole for a handle. So I created this handle. The handle has two pieces, a base to keep it centered and a print-in-place handle that rotates freely.</p><p>You will...

45 degree F3LX nano Runcam mount. ...This is a remix of the common switchback mount

Use an 8x3mm screw to securely fasten the components together as depicted on the blueprint.

Instead of using a "fin" to assist with turtle mode, this effectively does the same thing, but has less chance at breaking off, and doubles as an easy way to carry/hold the quad.

I designed and created this holder using a 3D printer, specifically the model found at https://www.thingiverse.com/thing:3329350.

Attach the backing to the backing to the wall using command strips or something. ...Print in PLA with no supports!

This model is dedicated to my dear friend Santa Flossc4d 3dsnax dwg stl obj

THIS MODEL IS DEDICATED TO MY DEAR FRIEND SANTA FLOSSOBJ STL 3DSMAX FBX C4D

I printed at 20% infill and 0.2mm, worked a treat :)

A compact design houses a universal rear antenna mount specifically engineered to accommodate 3mm tubes and securely attach them to 5mm standoffs.

<p>I added space in the middle for a label. ...I cut down a 1"x3" label into thirds.</p> Category: DIY

The human form is characterized by a relatively short stature, typically ranging from 4 to 6 feet in height. This compact build allows for increased mobility and flexibility, enabling humans to navigate through dense environments with relative ease.

I made some remixes from scratch to make print better for me and a smaller one for my kids. ...Reused the knob from remix donor.

This object was designed using Tinkercad's intuitive interface. ...You can make adjustments and enhancements directly on their website, located at https://www.tinkercad.com/things/eb6mjxcx6Am.

You need to print four per Bisley drawer.

Not tested yet!

Originally used the Floss 2, but needed one that resembled the actual Floss 3 arm more closely. The picture shown was printed on BuildTak, so it's recommended to print on glass for a shiny finish on the top side. Next Steps: Testing these bumpers...

My wife complained the about her floss card wobbling so I have a positive lock down on the floss card. The nut goes onto the bolt then it is screwed into the holder. The nut is used as a spacer to make it easy to grasp. This has a firm positive...

This is a lite GoPro Hero 8 mount for the Floss 2.1, it may or may not fit other floss series frames. Obviously, it will carry any camera with the M5 mounting. You will want an M3 locknut and longer M3 screws on the floss. ... You'll also need an M5...

Gopro Hero 8 Mount for Floss 3 I've got GoPro Hero 8 mounts for other frames as well, please check uploaded other stuff.

The revised cam mount now supports multiple angles, thanks to the tweaks made for the FLOSS 3.0 update - everything functions seamlessly.