r xsr 3d models

r-xsr diatone er349

protection r xsr

20x20 Frsky R-xsr mount.

This mount is to save your R-XSR Receiver. ...

R-XSR for 20 x 20 Mount. ... Sized for heat shrink to help hold antennas.

A simple mount for securing a Frsky R-XSR to the top of your FC stack Features an "Antenna Clamp" to secure the UFL connector to the board and stop the connector being ripped off the board in the event of a crash

This is a holder for FrSky R-XSR receiver on QAV250 frame. It is adopted for 5mm smooth stands. 31.5mm between stands center. In case you need a different stand size let me know. On my printer the model need to be scaled to 101-102% in case of PLA...

Generally, you would use one of these for S-BUS (or inverted SBUS which you can get from the board, Google "inverted sbus r-xsr" to learn more) and one for smart port. The 4 bolts are 8mm M2 bolts. There are holes in the case for the...

FRSKY R-XSR mount in minimal size

Needed to mount R-XSR to MX3-Sparrow Frame.

FrSky R-XSR Mount to a 30x30 stack

Mount for R-XSR for standoffs on 30 mm spacing.

R-XSR mount for 16x16 stack. ... Suggest printing in TPU.

Lightweight R-XSR mount for the Kaidju R. ... Weight is 0.5g in TPU. The R-XSR connector fits between the carbon holes to save a maximum of vertical height.

Lightweight R-XSR mount for the Kaidju R. ... Weight is 0.5g in TPU. The R-XSR connector fits between the carbon holes to save a maximum of vertical height.

Rush Tiny Tank and R-XSR mount for a 30x30 stack

Simple mount for a FrSky R-XSR receiver so you can stick it into a 20*20 stack.

Simple housing case for FrSky R-XSR receiver. ...Two holes in the front can be easily used to glue 3mm antenna tubes.

This is a lite 20x20 mount for a Fr-Sky R-XSR SBUS receiver I made quickly for my micro quad.

This is a lite 20x20 mount for a Fr-Sky R-XSR SBUS receiver I made quickly for my micro quad.

This is a small plate to mount a FrSky R-XSR receiver to a 30mm stack. ... I printed it from TPU and used a pair of zip ties to add some extra friction and function as antenna mounts.

3 different Frsky R-XSR mounts for your Armattan Chameleon TI frame. Printed in TPU, no supports. ... Suggest maybe wrapping a small zip tie around the RXSR once it's in the mount for security.

I use an R-XSR on a 270 size helicopter. I wanted the RX to be enclosed and I wanted room to wrap the antennas inside the case and only expose a small bit of them. I printed this at .2 in PLA. ...I tried at .1 and it didn't work as well.

I probably over engineered the crap out of this but as I am new to 3D printing and Fusion 360 I went a little over the top. ... Anyway, this is a part to house the R-XSR. ...it has mounting holes 20mm apart as well as holes for 3mm antenna poles.

So I added a R-XSR box to the back and made antenna holes. I then thanks to 7-11 hot glued some straws to the upper plate and routed the antenna. I made sure the antenna wouldn't get cut during vibration by inserting some heat shrink tubing. ...

for mounting R-XSR receiver on quatcopter.

RX Mount for Tyrp 79 (R-XSR)

R-XSR Mount for Xilo phreakstyle. ... Enjoy!

Frsky R-XSR 30.5mm Mount. ...With and Without SMA Holder

Lightweight mount for Unify Pro 5V with room for a FrSky R-XSR receiver underneath.