r xsr receiver 3d models
69908 3d models found related to r xsr receiver.cults3d
This is a lite 20x20 mount for a Fr-Sky R-XSR SBUS receiver I made quickly for my micro quad.
thingiverse
This is a lite 20x20 mount for a Fr-Sky R-XSR SBUS receiver I made quickly for my micro quad.
thingiverse
Mount for Frsky r-xsr Receiver and FPV video antenna. ...Works best with flexible filament.
cults3d
Mount for Frsky r-xsr Receiver and FPV video antenna. ...Works best with flexible filament.
thingiverse
FrSky R-XSR receiver case w/button. Material to make top: SBS, Neylon (PA),Petg. ... Material to make case: any.
thingiverse
A very basic plate that has a cable tie slot to allow mounting a r-xsr receiver into the wing of a s800. ... Glue the plate into the wing, cable ties can be replaced without needing to remove the plate.
prusaprinters
Works best with flexible filament. Print instructionsCategory: R/C Vehicles Summary Mount for Frsky r-xsr Receiver and FPV video antenna. ...Works best with flexible filament.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong> Prusa</p>...
thingiverse
This is a receiver mount for the Frsky R-XSR receiver for the Diatone GT-M200 or I think several of the Diatone GT frames. It screws into place with a couple of short 2.5mm screws. It keeps the antennas away from the props, but also away from carbon...
thingiverse
This is a simple R-XSR sized receiver mount with antenna provisions and some stabilization support for the rear arms of the drone to prevent movement after a crash. This item is intended for use with the TBS unify style VTX plate and will not fit...
thingiverse
This is a little mount for the R-XSR receiver from FrSky. It is designed to be next to a Matek VTX-HV and has a small spot for a zip tie to secure the VTX antenna pigtail. ...It doesn't have to be used with the Matek VTX however.
thingiverse
This is a support for micro receiver like Frsky R-XSR or another in a Diatone GT-R90. ... Happy flying!
thingiverse
Front mount of receiver FrSky r-xsr for Geprc mark4. Print with supports which can be easly removed by flat screw driver (attached to ender3) and small hit. ...Use zip tie to hold receiver in place.
thingiverse
Well, as I thought about that, I came up with the idea of not only having an antenna mount, but also a mount for the R-XSR itself. 2 things up front: a) the slot for the receiver is designed to be a tight fit! I don't wanted my Rx to fall out by...
thingiverse
Rotate the gold IPEX connectors on the receiver to match the direction of the antenna-tube. Feed the antennas through the holes, then insert the antenna-tubes. Make sure that the bind button is facing down (facing the open side). A dab of...
thingiverse
Design Objectives - Able to mount a Frksy R-XSR Receiver - Works with both TBS Unify Pro style pigtail as well as a regular hex shape pigtail. - Lock in pigtail in place to prevent it from rotating. - Able to print without support. - Keep...
thingiverse
This thing is a mount for a R-XSR receiver and its antennas, for a Dragon HX5 frame (from Banggood). The part replaces the small carbon plate on the "head" of the drone (above the FPV camera). The M2 screws of the original part can be used. To...
thingiverse
TPU protections for a better antenna tight and F-port solder. ... Use heatshrink tube to cover as in the pictures.
thingiverse
A minimal design made for racers who plan to use shark fin at the back and will mostly flip using back props. ...Purposely made to be flimsy to give during impacts
thingiverse
FrSky R-XSR RC receiver mount for DJI450 type frames
thingiverse
Holder for Frsky R-Xsr receiver. ...30x30-3mm holes for micro drones.
thingiverse
Lightweight mount for Unify Pro 5V with room for a FrSky R-XSR receiver underneath.
thingiverse
Simple mount for a FrSky R-XSR receiver so you can stick it into a 20*20 stack.
thingiverse
Simple housing case for FrSky R-XSR receiver. ...Two holes in the front can be easily used to glue 3mm antenna tubes.
thingiverse
R-XSR receiver & UNIFY NANO video transmitter mounting plate for standart 30.5 x 30.5 stacks.
thingiverse
This is a small plate to mount a FrSky R-XSR receiver to a 30mm stack. ... I printed it from TPU and used a pair of zip ties to add some extra friction and function as antenna mounts.
thingiverse
This is a holder for FrSky R-XSR receiver on QAV250 frame. It is adopted for 5mm smooth stands. 31.5mm between stands center. In case you need a different stand size let me know. On my printer the model need to be scaled to 101-102% in case of PLA...