r8 modified 3d models

... the modified bridge fixes all of these problems. I also modified the bridge to have less excess plastic, and to lower the IPD from it's initial 80mm down to ~69mm. ... I'm still unhappy with the IPD, so I might try modifying it more in the future.

Thicker materials may have difficulty in bending so the design might need to be modified. Once the cut is done: 1) Attached to headband using original hole pattern. 2) Bend PETG extended protion back and attach to end holes on each side to head...

A modified fs-cover for the mmu2s upgrade that attempts to solve the IR sensor issue. The original model is modified by adding a small tab to the left side which accepts an M3 standard nut and screw. The screw pushes down on the extruder, causing the...

Max model has meshsmooth modifier intact with 49553 polygons. All other models are exported with meshsmooth collapsed at iteration of 1 (194345 polys). ...

This Modified Laptop Stand is also equipped with compartments on either side to give students the liberty to organize loose papers and even smaller sections on top to place smaller items like pencils and pens and even an external mouse. Now that...

This Modified Laptop Stand is also equipped with compartments on either side to give students the liberty to organize loose papers and even smaller sections on top to place smaller items like pencils and pens and even an external mouse. Now that...

Here's the modified version of http://www.thingiverse.com/thing:46887 to support a phone case. I've expanded it to 15mm wide. I used Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=46887) to create this design. ... The settings...

Modified design for the tail section of Tom Stanton's original Paramotor design takes center stage. To prevent a nasty break to the prop guard, some 'skids' or support struts are added. This modification makes it less likely that the prop guard will...

Consequently, I modified the original design to eliminate interference with the eye mechanism while preserving the same side profile without the need for a speaker installation. ...The speaker could still be installed, but in that scenario, it would...

... Rod Connector Part 1 (v3) is a remix of Pool Pole Clip by thetazzbot . Great model but i needed bigger pins and a few other modifications. *** this model is a remix of "Swimming pool vac to shop vac attachment converter" but with a modified fit

First I modified the hook for easier printing. It includes pillars and a wall that can easily be cut away after printing. No support is required anymore. Second, I made it less pointy and added a bevel to the top and bottom edges. I'm using it...

... design, I lengthened the bottom portion of the clip for a more secure grip. If anyone prints this modified version, please share your feedback on how it fits and whether any adjustments are needed. ...Currently, my 3D printer is out of commission.

I've also created and modified other brackets to accommodate them seamlessly. So when I saw this new design, I knew right away what my next project would be. It turned out fantastic and I'm thrilled you're going to love it!! UPDATE: I've also...

I Modified the Y Tensioner Bracket to Fix Fouls between the Bracket and the Y Carriage. It Now Clears Everything When Fitted Flush to the End of the V-Slot Extrusion. I Redesigned This Bracket from https://www.thingiverse.com/thing:3694789. ... I Also...

Modified the curves slightly to avoid having the filament pop off and added a bit of height to make them easier to handle. Drawing is a VariCAD file. I should add that this design was specific to 3 mm filament, not sure if it will scale for 1.75...

Modified Spool Holder Designed Specifically for the Deltatrix 3D-Printer with Bearings Spools with a minimum inner diameter of 26mm and a maximum width of 125mm will fit seamlessly. You'll need two bearings, each one being a 6003-2RS model, as well...

I Modified the original cover in order to include my initials in the cover. you will need the original .stl as import file in order for my hack to work. I also added a space for a 6x9mm magnet to be inserted into the cap, if you are playing at a...

I've modified several parts to fit my 9mm XL650 and how I want to attach the OBF. I'm using a 25x25mm, 800mm high aluminum table leg. Additional threading was added making it much easier to connect the DAA large spring on both the hopper and drop...

Modified this Mech to take my ESP32-Cam was worried about the heat but so far no failure. The original poster of this model was given the blues for it. If you can't figure out what to do with it don't make it. the camera needs to be hot glued to the...

This is a Modified prusa shield mask that can rotate and make the shield go up or down, giving the user an option to cover or uncover the face. I couldn't find a transparent plastic cover so i used an old A4 format x-ray image instead :). The...

... schlage tool would have worked fine, except the lever has a tailpiece that doesn't separate from the plug. For this reason, if I pushed the cylinder out with the standard tool, or the modified tool, all of the security pins would have come out.

when you stuck on urgent condition, with limited time & cost..sometimes everything around you can be modified into something that you need...creativity is the key (best part of creativity in engineering on your head will come up when you stuck on...

This is a modified version of the Open Drag Chain. It eliminates the unnecessary through hole that doesn't make sense for FFF printing. The result is the part prints slightly faster and slightly cleaner. The original author requested I remove the...

To address this issue, I modified the fingers of the robot's jaws to improve their ability to grasp round objects more effectively. The modifications allowed the jaws to accommodate a heavier steel ball bearing with a concave surface that enables it...

This modified design of the socket was crafted by tropics specifically for my use, available at https://www.thingiverse.com/thing:812793. The circuit used in the tester visible on the photo can be accessed here:...

The Arduino Uno was modified according to datasheet recommendations, and the project was designed using Altium software, with electronic components sourced from DigiKey. The CAD files were created in SolidWorks and rendered using KeyShot. Watch...

Instead of taking a file and using a dremel to modify a plastic/resin part, I decided to adjust a STL file for the opening that I needed. Now I can display all lines of my LEDs without rows being obstructed from view. This project was created with...

I didn't like any of the existing inmoov ear's that don't have speakers in them, and i didn't want one that looked like an actual ear, i wanted something still sort of classic robot looking, so this is what i came up with, i also modified them to...

This is an upgraded version of endstop_z from Tobeca.\nThe scad file leverages the open source files generously provided by Tobeca.\nWhile this modified version does not necessitate precise fixation with screws, I've added some for stability anyway,...

This modified microphone clip has been altered to make its base and attachment more durable. The model's technical specifications include threads measuring 5/8" x 27 TPI, although they are not visible in the image due to the thread density being...