raceflight 3d models
26 3d models found related to raceflight.thingiverse
... ...Its designed to hold the raceflight 25v 2200 capacitor and a 35v 1000 capacitor, the tabs on the side are designed to go above and below a 5mm racing arm with a little bit of extra space for wires that doubles as protection for your motor wires
thingiverse
Simple capacitor holder for your Raceflight Bolt capacitors. Works with the 25V-2200uF capacitors that come with the Bolt 4-in-1 ESC. Fits the FPV-Flightclub Tokio quadcopter frames (and probably others). Arm dimensions: 4mm (thickness) x 17mm...
thingiverse
Back LED holder for Shendrones Raceflight Orca frame. Led is tilted 35 degrees. Suitable for Adafruit Neopixel Jewel (23mm diameter). Mount with back canopy screw. Ziptie led to the mount. I run led cable through the bottom plate. Same hole is used...
thingiverse
... to me way too tight on the camera, it felt like I was breaking it. ...These offer a bit more clearance. This was originally designed for the 3" Big Deal Raceflight Kit but in theory these will work with any micro cam if your stand offs are 30mm apart.
cults3d
This was designed for the Fighting Rooster build. ... YouTube https://youtu.be/A_-5wU9x08k
thingiverse
This was designed for the Fighting Rooster build. ... YouTube https://youtu.be/A_-5wU9x08k
thingiverse
Dual 8mm cap holder for the RaceFlight / FlightOne BigDeal 3inch kwad.
thingiverse
This was designed with the Raceflight Bolt 4-in-1 ESC in mind but can be applied to many standard size race and freestyle drones,
thingiverse
FlightClub Proton CAPs mounts for RaceFlight Spark32 printed in TPU 20 x 20 mount with M3 x 3.2 L inserts space under for Spektrum SPM4649T still, room for RaceFlight MilivoltOSD & HGLRC TX20 V2 on top make holes bigger HGLRC larger
thingiverse
Designed for SP Racing, Betaflight, Raceflight or else. Versions : 1.00v * Released on 3/14/18. 1.01v * The plate thickness is now 1.60 mm. It was 1.50 mm before. * I changed the triangles shape to hexagons. * I changed the...
thingiverse
... specifically made for FCs using gummies. ...I made the shafts larger for a snug fit with the gummies, it should not move. The t in the center is the greek tau which is used in our logo at TorqueFPV. I am using it with a Raceflight MilivoltOSD. ...
prusaprinters
FlightClub Proton CAPs mounts for RaceFlight Spark32 printed in TPU 20 x 20 mount with M3 x 3.2 L inserts space under for Spektrum SPM4649T still, room for RaceFlight MilivoltOSD & HGLRC TX20 V2 on top make holes bigger HGLRC larger Print...
thingiverse
I found those ESC covers for 10A LittleBees and resized them to find the perfect fit for the RaceFlight 30A ESC (BumpBee30A)... I like the design since printed in TPU I can just snap them onto my already solder ESCs without having to desolder...
thingiverse
I used foam tape to tape my FC (RaceFlight Revolt) to the adapter. The little pins are just to aid alignment when putting it down on the foam. I had another design that used holes, screws and o-rings but it was more of a pain. Feel free to tinker...
thingiverse
... ...Chopped some different holes for the location of a default install of the RaceFlight Revolt FC. Added a finger hole for VTX changes when it's sitting on top of the FC (TBS Unify). Also added a TBS Unify slot for the antenna so it stays in place.
thingiverse
I couldn't find anything online to buy same as the Revolt FC (Raceflight) dampening washers and I created one :). You will need to drill your FC mounting holes so the washer can fit in and allow a M3 screw to pass through. The outer wall diameter of...
thingiverse
The Raceflight esc will not fit but that version will follow soon. This version is made for the HS1177 style cams and has a cam angle of 15 to 45 degree. Print the pod that fits your cam and print it in the color you like. This pod is designed to be...
cults3d
We ran a Naze32 but intent to fit a Raceflight Revolt soon. The frame is big enough to run 3.5" props which we would recommend. After using only 3" props we upgraded to 3.5x4.5" props for better flight characteristics. This quad frame would be an...
thingiverse
Was Ihr alles noch dazu braucht: Filamente: Carrbon colorFabb XT-CF20 - 2,85 mm oder halt was ähnliches PLA Snowwhite oder… Montage: 8 x M3x25mm für das Frame 16 x M3x10mm für die Motoren Hardware (welche ich verbaut habe): RaceFlight Revolt F4...
thingiverse
We ran a Naze32 but intent to fit a Raceflight Revolt soon. The frame is big enough to run 3.5" props which we would recommend. After using only 3" props we upgraded to 3.5x4.5" props for better flight characteristics. This quad frame would be an...
pinshape
We ran a Naze32 but intent to fit a Raceflight Revolt soon. The frame is big enough to run 3.5" props which we would recommend. After using only 3" props we upgraded to 3.5x4.5" props for better flight characteristics. This quad frame would be an...
thingiverse
Using: [F3 AIO flight controller](https://www.banggood.com/Holybro-Kakute-AIO_v1_0-Cleanflight-Raceflight-Betaflight-32-bit-Flight-Control-w-OSD-PDB-p-1097723.html?p=KN090889143662017021) [ESC...
thingiverse
Different flavours of Flight controllers: http://www.banggood.com/Raceflight-Betaflight-CC3D-REVO-F4-STM32F405-Flight-Controller-with-VbatBuzzer-p-1087561.html?p=BQ31181713038201505L...