rackmount edgerouter x 3d models
324803 3d models found related to rackmount edgerouter x.thingiverse
I recently purchased a new Ubiquiti Edgerouter for my home network, and couldn't find a rack mounting solution. This is what I came up with to solve the problem. *v0.1* my first attempt needed some filing to fit the front plate of the router...
prusaprinters
I recently purchased a new Ubiquiti Edgerouter for my home network, and couldn't find a rack mounting solution. This is what I came up with to solve the problem. v0.1 my first attempt needed some filing to fit the front plate of the router correctly,...
thingiverse
Just a remix of a great design so it doesn't need screws to mount the Edgerouter X.
thingiverse
On the UBiQUiTi website I saw this rack mount kit, ER-RMKIT, which was designed for EdgeRouter 4 and EdgeRouter 6P. However, in addition to their mounting holes, both of these routers had bigger dimensions than my EdgeRouter LITE. So, I knew if I...
thingiverse
I designed these rackmount ears for my EdgeRouter 10X after failing to find any equivalent for my router. I've had this setup in my rack for about a month now, and it seems to be really sturdy. ...Hopefully, this will help others in the same situation.
thingiverse
Simple stand for my Ubiquiti EdgeRouter X SFP for better cooling. ... For EdgeRouter X: https://www.thingiverse.com/thing:4256748
thingiverse
This is a desktop stand for the Ubiquiti Edgerouter X. ...Print it laying down for best results.
prusaprinters
This is a desktop stand for the Ubiquiti Edgerouter X. ...Print it laying down for best results.</p> Category: Electronics
prusaprinters
<p>Designed to make it blend in better on my white wall. ...For the Edgerouter X non-SFP model. Press-fit.</p> <p>For use with PoE! ...No hole for PSU connector included.</p>
thingiverse
1U 19" Rackmount for Ubiquiti Edgerouter 10x with cablemount. The two additional screwhols are used to connect multiple Rackmounts together. ...
thingiverse
For the "EdgeRouter X" from "Ubiquiti", to mount on a DinRail. ... I used "nylon", because this material is quite flexible for the DinRail clip.
thingiverse
Added nubs to help hold the EdgeRouter X in place & holes in the back for power, ground & reset access. I added chamfers and fillets to the edges to make them easier on the hands and to look nicer. ...Also, I have not yet printed this so it is a work...
thingiverse
Hanging mount to easily hang and remove a Ubiquiti EdgeRouter X using the standard screw-mounting holes on the back. Works best in orientation where status lights are at the top, but interference fit could be enough for other orientations. I...
thingiverse
Bracket to mount a Ubiquiti Edgerouter X to a smooth surface (e.g. the side of a shelf) using Tesa Power Strips (large). Should probably also work fine with 3M Command Strips. ... Print with the flat side down and supports enabled.
thingiverse
I use the following parts aside from the 3d printed one: 1x DINM12-RC from Winford: https://www.winford.com/products/dinm15.php 2x M4x12mm flat head screws: https://www.mcmaster.com/91698A430/ 2x M4 lock washers: https://www.mcmaster.com/97099A103/...
thingiverse
This is a simple bracket to mount an Edgerouter X onto a DIN rail. It uses a DIN bracket like this one: https://amzn.to/3je8HEK I used 2x M3x12 screws and nuts to secure it but I also added ears so that you can also just use a zip tie to secure...
thingiverse
A pegboard mount for the *Ubiquiti EdgeRouter X* network router that uses the EdgeRouter's wall mount holes to fasten to the mounts. No more zip ties! No more drilling! Want to rewire the network for the 3rd time this month? Just pop the mounts off...
thingiverse
1U rack bracket for the Ubiquiti EdgeRouter X SFP. ... Use two zip ties (or one very long one) through the hole to fixate the router.
thingiverse
Remixed from: https://www.thingiverse.com/thing:3406735 Ubiquity EdgeRouter X Wall Bracket by kielo https://www.thingiverse.com/thing:3734897 IKEA Skadis Peg Models by Rkimmell73 Printed upside down (board pegs up), with tree supports and 100%...
thingiverse
Ubiquiti Edgerouter X SFP RACK mount. I wanted to mount one UBNT Edgerouter X into my RACK. I couldn't find a model for the SFP version, so I have created my own. I took some inspiration from https://www.thingiverse.com/thing:3045297 but I have...
thingiverse
The EdgeRouter X has to have the rubber pads removed to fit into the slot where it is secured with two M3x6mm screws and washers. ... Source:...
thingiverse
A rack mount to install a Edgerouter X next to a Unifi Switch 8 150W in a 19" rack.
thingiverse
remix of a remix i only changed the lip on the top of print (face side down) so that one thing doesnt need supports. whoops, somehow rotated on export. ...make face side printer down of course (:
thingiverse
This is a remix of someone else's design. All I have done is moved the mounting holes in by 2mm each so that it is compatible with a 19 inch rack. ... Position the print on the bed so that it is face down and you won't need any support or rafts.
thingiverse
APU1-6 Rackmount Remix of https://www.printables.com/de/model/76650-pcengines-apu2apu3-modular-rackmount-remix