radds 3d models
79 3d models found related to radds.thingiverse
Precisely located holes and slots for the RADDS SD card and reset button, Due USB ports and power input connector. Mounting tabs to allow attachment to 20mm extrusions with up to 5mm screws. Slots to allow a small screwdriver to be inserted to pry...
thingiverse
Mount for Arduino Due with RADDS shield. ... Holes are for ISO 7380 M5 screws. Check out my RADDS cooling solution.http://www.thingiverse.com/thing:841122
thingiverse
This is a holder designed to hold Arduino RADDS on a 2020 Aluminum extrusion. ...
thingiverse
Mount for Arduino Due and RADDS. ...It have a mount for cooling fan. I try to make the air from the fan flow on the ARM processor under the RADDS Shield.
thingiverse
This is a model of the RADDS Extension Board V3. ...Also checkout this great thingie which I based my design on: https://www.thingiverse.com/thing:697173
thingiverse
... is to hide the wiring and get a clean look. okt. 2014 - a user reported problem when sliceing the RADDS_DUE_housing, so I have uploaded a new file RADDS_DUE_housing_2ps (hope this one is ok) Instructions I printed mine in PLA with 0.2mm layers.
thingiverse
Carefully think about the microstepping you plan to use - now and in the future - and make sure you set the switches on the bottom of RADDS accordingly before you insert it into the case - It can be very tricky to get it out of the box afterwords,...
prusaprinters
This is a model of the RADDS Extension Board V3. ...Also checkout this great thingie which I based my design on: <a href="https://www.thingiverse.com/thing:697173">https://www.thingiverse.com/thing:697173</a></p><h3>Print instructions</h3><p>Category:...
thingiverse
A two part enclosure designed to attach to alloy extrusion and hold a Radds LCD screen with a swivel / tilt mount .Compact thickness (only 20mm thick) by using 4 x 3mm through holes in PCB as case screw fixings, one 2 screw mount for 40x40 alloy...
thingiverse
RADDS holder (primary for my delta printer) mount fot noctua A9-x14 place for PWM regulator
thingiverse
Some models I made to make it easier to design housings and mounts for my printers. I have not included all parts like SMD, and I cannot guarantee that the models are 100% perfect. ... 10.10.2015 Uploaded my step files - important, these models are not...
thingiverse
:-) Credits go to user mundsen (http://www.thingiverse.com/mundsen) for providing the STLs of the RADDS hardware. UPDATE: Added two mounts for cooling fans for Arduino / RADDS. One of them is sized to fit a 40x40x10 mm fan under a 2020MK. ...The second...
thingiverse
Credits go to user mundsen (http://www.thingiverse.com/mundsen) for providing the STLs of the RADDS hardware. Instructions I've printed all parts with 0.1 mm layers on bare glass (@ 60°C). ...The...
thingiverse
This is an adapter that allows you to mount a RADDS printer controller in the Wanhao I3 controller box. I have also included a replacement front for the older enclosures. ...This is where I brought out my LCD cable and have a USB connector mounted.
thingiverse
This is a simple holder for the RADDS Hall-E-Endstop on a 8mm rod. The visible endstop is from the following repository https://www.thingiverse.com/thing:697173 i cut direct M3 threads into the ABS. ...For the electronic i used plastic screws.
pinshape
the Radds box has a mounting area on the back plate for a 30mm fan and a micro usb to usb-b adapter and the on off switch that comes with the duplicator i3 . but it still does not house the psu .. i might make a different version to acomidate the...
thingiverse
and also created a Radds v1 enclosure for people that have Radds . the Radds box has a mounting area on the back plate for a 30mm fan and a micro usb to usb-b adapter and the on off switch that comes with the duplicator i3 . but it still does not...
thingiverse
I created an enclosure for my RADDS 1.5 board. It's _not_ snug fit, there is enough space to insert (and remove) the electronics without any force. Use four M3 screws and nuts to mount the electronics and two M5 screws to mount the enclosure to some...
prusaprinters
keep enough to re solder into the holes on the board so all white connectors are facing upward. and also created a Radds v1 enclosure for people that have Radds . the Radds box has a mounting area on the back plate for a 30mm fan and a micro usb to...
thingiverse
This is yet another LCD case for Radds. I have used a knob from my generic knob project: https://www.thingiverse.com/thing:3320759 Requirements for the project was: Ability to angle display Printable in PLA Design everything from scratch ...
thingiverse
But it is my housing for a RADDS board with Arduino Due and LDC screen. Feel free to let me know of any errors or issues you see or find. Once I've printed one, I'll put up pics. Doubtless it needs tweaking. I'm just sticking it here in case my...
thingiverse
Case for RADDS Display and 2 switches. Switches are Marquardt 1801 series. You need a drop of instant glue to mount the buttons. ... Please share your makes!
thingiverse
Hier mal meine erste Version des Gehäuse für den Arduino Due mit Radds V1.2 Es ist auch ein Deckel mit 10mm Rand dabei damit der Lüfter auch drunter passt ;-)
thingiverse
This is a simple, yet useful ;), adaptor for adding a 80mm fan to RADDS electronics. The fan shown in photos is 80x80x15mm. Screws used: 6mm M3 x4 -> For holding the adapter to RADDS 20mm M4 x4 -> For holding the fan to the adapter. IMPORTANT: Length...
thingiverse
Decided on Due-Radds 32 bit controller for new 3D printer, looked around for an enclosure and found this one:-https://www.thingiverse.com/thing:693670 But for me it was unnecessarily large, did not have cable connection openings as required or SD...
myminifactory
This is a case for the RADDS LCD/SD-Display with Reset- and Back-Buttonhttp://max3dshop.org/index.php/default/elektronik.html?___SID=U I tried to design a slim enclosure again using a channel outside between the top and bottom part to let the case...
cults3d
This is a case for the RADDS LCD/SD-Display with Reset- and Back-Buttonhttp://max3dshop.org/index.php/default/elektronik.html?___SID=U I tried to design a slim enclosure again using a channel outside between the top and bottom part to let the case...
thingiverse
This is a case for the RADDS LCD/SD-Display with Reset- and Back-Buttonhttp://max3dshop.org/index.php/default/elektronik.html?___SID=U I tried to design a slim enclosure again using a channel outside between the top and bottom part to let the case...