radio bracket 3d models
85786 3d models found related to radio bracket.thingiverse
Dial guage mount designed to mount on the front of a 4015 blower. Remixed from https://www.thingiverse.com/thing:2519296 Fits 57mm guages. Mounted with 2x M3x20 bolts. ... Printed at .3mm layer height, 15% infill.
thingiverse
Customized version of https://www.thingiverse.com/thing:2913687 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2913687
cults3d
Remix: - https://www.thingiverse.com/thing:4699747 Purpose: - Adjustable mount for Z-Stepper Required: - M4 bolts (4020 rail mounting) - M4 t-nuts - M3 bolts (stepper mounting)
thingiverse
Customized version of https://www.thingiverse.com/thing:3675765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3675765
prusaprinters
<p>This is a holder and waste basket for the Filament Cutter <a href="https://www.prusaprinters.org/prints/67509-filament-cutter-45deg">https://www.prusaprinters.org/prints/67509-filament-cutter-45deg</a> designed by Pomi.</p><p>The idea was to...
thingiverse
Smart Filament Sensor rear cap to install on a 3030 extrusion
grabcad
This will mount a SkyFlar Strobe unit to the rear of the center spar on a Gravity Defy Paramotor. ...It uses 3 zip ties and is designed to have a strip of 3M double sided foam tape in the center channel.
thingiverse
Simple mount for generic power switch from chinese toys. Might be useful if you want to install LED strip on your Ender 3 printer. ... No supports.
thingiverse
Customized version of https://www.thingiverse.com/thing:5516701 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5516701
thingiverse
This is a minimalist approach for mounting your ATX PSU. ...Features : Quick to print Does fit most ATX power supplies
grabcad
Topology optimized shell and lattice (walls) structure. ...Final mass 27.7 grams.
grabcad
Full 3D solid topology optimized of shell and lattice structure. ...Final mass 0,0575 lb(26.1 grams).
thingiverse
Customized version of http://www.thingiverse.com/thing:1523711 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1523711
thingiverse
Customized version of http://www.thingiverse.com/thing:1523711 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1523711
thingiverse
Customized version of http://www.thingiverse.com/thing:1259325 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1259325 Instructions Using the following options:...
thingiverse
its thick enough to be stable. thin enough to work and closer than the stock mount. this mount is within 1mm of the bed when the bltouch plunger is depressed. it is not 5mm away. making your "baby z stepping" more manageable and easier to eye up. i...
cults3d
I loaded up the original .stl in Cura and Craftware they seemed to show that it would print solid. I installed MatterControl and loaded it up and it looked like it would print with holes. I don't like to connect my PC to the printer for prints...
cults3d
Remixed to move the end stop 2mm higher so it works with the mgn12 rails, the original only just catches the limit switch.
prusaprinters
<p>I was working on adding linear rails to my Ender 3, however with the <a href="/make:899298">Z axis linear rail setup</a> I'm using, it originally requires to buy new screws for the Z axis, and at the time I was building it I didn't have any extra...
thingiverse
J'avais besoin d'une équerre d'angle pour des étagères triangulaires, qui mesurent 25x25cm. J'en ai donc dessiné ! Profitez-en ! 1e version. ******** I needed a corner square for triangular shelves. It is designed for a width of 25x25cm. So...
thingiverse
Customized version of http://www.thingiverse.com/thing:2448362 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2448362
prusaprinters
<p>Didn't have the build volume working to do the full size, so I cut things down to just work on the left side.</p> Category: 3D Printer Accessories
thingiverse
J'avais besoin d'une équerre d'angle pour des étagères triangulaires, qui mesurent 25x25cm. J'en ai donc dessiné ! Profitez-en ! 2e version. ******** I needed a corner square for triangular shelves. It is designed for a width of 25x25cm. So...
cults3d
Allows the media mod to be mounted via a hot shoe point. This means the inbuilt feet don't need to be deployed and subsequently it is much easier to changeover batteries and SD cards without removing the go pro from an attachment. ... Customization...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gEOMgdc84sq IF you rotate the part to print on it's side,
thingiverse
Spool holder for on top of the printer to take up less space in your room.
thingiverse
I wanted to mount the LCD on the left hand side of my Ender 5 without impacting the bed movement as well as make it in a front mount configuration.
thingiverse
Mounts on a standard Ender 3 hotend (next to the cooling fan). ...Fits 18 mm sensor by default by could be modified to use any size sensor.
thingiverse
Customized version of https://www.thingiverse.com/thing:3406258 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3406258
cults3d
Suitable for attaching a CR-Touch auto bed leveling probe using the two bottom screws of the extruder assembly. Use PETG for flexibility and resilience. Support is built-in, no additional supports are needed. ... Tinkercad design available here.