radiolink ts100 3d models
742 3d models found related to radiolink ts100.thingiverse
... will fit as to create the pole. tip: bn880QtopPole.stl goes inside the main case !! - i used sainsmart TPU wich is semiflexible not the rubbery type - Also works with radiolink TS100, SE100, bn880 gps units. post some pictures. ...cheers.
thingiverse
Shark fin for installation on the frame series XL7. ...Designed for the installation of gps Radiolink TS100. ...Printed by ABS plastic with supports.
thingiverse
VTX SMA Connector holder & GPS Radiolink TS100 holder for Iflight XL5 V3 drone frame. Press fit on standoff. ... Two separate models.
thingiverse
Support for the Radiolink TS100 GPS in the front of the Martian IV frame. Is designed to be printed in TPU (the case of the TS100 is strong enough, I think TPU will be better to maintain it in place after crashing). ...
thingiverse
Support for the GPS Radiolink TS100 in the top of the Martian II frame. The GPS is tiny, and has it's own case, so the support is only to let the GPS in a fixed position and help in some crashes. Changed by a V2 version, the V1 does not hold the...
thingiverse
2 Version remixed from 450 Heli tail compass mount by mosteveo tks V2.0 has bigger holes for the Zip Ties
thingiverse
Here's a gopro-style mount for your piece of equipment (phone holder, lcd display for fpv, name it.) on your Radiolink AT9/AT9S. ...Haven't tried but it should fit on other Radiolink Transmitters.
thingiverse
Sticks for m3 ghimball like Hitec, Radiolink and FRsky. ... I use these sticks to have mor precision on the controls and to be more comfortable with two fingers.
thingiverse
Just a quick mock-up of the Radiolink R4EH-G Receiver in case someone wants to design a holder for it.
thingiverse
Radiolink At9 gimbal protector. ...Two models: height 26mm (protectores stick) height 21mm (protectores stick_corto), It does not completely protect the stick
thingiverse
This is designed for the Radiolink GPS (SE100) - https://www.amazon.com/dp/B01IUSVXOA/ You have to remove the radiolink gps from the original housing, and put it in the printed one. ... If you like what I've done, please consider sending a donation: ...
thingiverse
Transmitter Holder for Radiolink AT9S Suitable for other transmitters which has 5mm metal holders. ...(Futaba, JR, etc...) Total 15 Parts to be printed, use epoxy adhesive to fix the parts together.
cults3d
Transmitter Holder for Radiolink AT9S Suitable for other transmitters which has 5mm metal holders. ...(Futaba, JR, etc...) Total 15 Parts to be printed, use epoxy adhesive to fix the parts together.
thingiverse
Radiolink AT9 lcd/screen/phone/whatever you want holder, and models for screen i use. ... For this screen model, you need; Car TFT LCD 5" Boscam TS832 Receiver I use 4 Brass inserts (1 in each corner) Print Settings Printer Brand: ...
thingiverse
This is an FPV phone mount for the RadioLink T8S. Just print 2x the Top Brace, and 2x the Bottom Brace, and connect these together with M2 bolts to go around the transmitter (see photo). ... Then print 1x the Phone Mount and use 2x 3M bolts to...
thingiverse
Additional handle for Radiolink RC4GS. ... Print, mount, enjoy one hand steering.
thingiverse
... при использовании батареек/аккумуляторов АА. Cover for Radiolink RC4GS and RC6GS remote control. Attention: Suitable only when using batteries! Tthis cap is thicker than the stock one. ...Therefore, it will not close when using AA batteries.
cults3d
Adattatore che consente di sfruttare le batterie Milwaukee M18 per alimentare i saldatori a stagno TS100