radion 7 3d models

Radion Aquarium LED Lights

Needed to mount radion extruision rails to hood. Hood has a lip of 18.72x30mm. ...Extrusion is 25x25mm.

This two pads are needed to level the Ecotech Radion fixture when using the original Ecotech Arm. The pads increase the angle of 5 degrees. For the external part I suggest to use a drop of hot glue to keep the pad in position. ...Moreover, I suggest to...

This is a radion light mount adapter for the OEM light mounting kit. This will adapt the front plate to fit on eurobraced tanks. This reuses the original hardware. Let me know if you have any issues or questions! EDIT: 2/12/2021 It was...

... go to your local hardware store and pickup a 1/8" rod. Assemble as shown in the picture using the provided eyelets from ecotech that come with the light. Designed for my printer which has a max bed size of 8", so this is approximately 7.5" tall.

The ecotech radion multilight mount is poor. The lights could tip over as there is nothing preventing this. This is a clamp for the multi mount that allows the mount to clamp to a eurobrace. It may work on a single light mount too if using...

Power supply holder for Ecotech Radion Xr30 pro

XR30 Gen 5 Ecotech Radion light shade. ...There is a right side and a left side that come together (the right side has an extra gap for the light cord).

This is a simple clamp to help hold your Radion diffuser in place and close any gaps that may form when the diffuser warps. ...Place one on each of the 4 corners of each fixture.

This is a surface mount for the ecotech radion xr30g6 pro aquarium light. I designed and printed it to use on 29 gallon biocube, but it would work on any hood. ...You will just want to cut out the portion underneath to allow the light to shine through.

Multi-Light Radion Mounting System - Slide Mount The Multi-Light RMS is a modular and customizable Radion LED mounting solution for the XR15 and XR30 systems. ...The RMS Slide Mounts connect your Radion LED to the RMS Track and allow for easy...

T-Nut for Ecotech Radion RMS bracket to mount on aluminum extrusion.

This is a mount for the Radion XR15 G5/6 light series, with an adapter to use this mount on a Red Sea Reefled mount. ... The Radion light mount can also be used without the adapter.

Print twice and they lock together with superglue gel. Apply mirror/chrome tape to inside for reflecting excess light down instead of across a room. ... Shown on G6 Blues

No description provided.

A simple slide on shade for my Radion XR15w LED Aquarium Light. Its is in my office near my desk, and the light as it glares in my eyes. ... Support Patreon : https://www.patreon.com/bigmrtong Patreon Preview : https://tinyurl.com/bigmrtong (everything...

A simple slide on shade for my Radion XR15w LED Aquarium Light. Its is in my office near my desk, and the light as it glares in my eyes. ... --------------------------------------------------- Support Patreon : https://www.patreon.com/bigmrtong ...

Picture is the shade on the center XR30 in my 265 gallon tank (Waterbox LX340.7). They're mounted using the Ecotech RMS mounts, so if you've got a similar setup, this will work great. Absolutely no direct light reaches the floor, it cuts off just at...

Got a 2nd hand mount and did not have a rimmed adapter to mount to aquarium- Pretty close fit the channel could be a little bit tighter, but it slides on smooth -

This is the spacer on RMS mount system

Ecotech Radion XR15 G4 pro quad power brick holder This also fits Vortech MP10/40 and Vectra M2/M1 Power Supplies.

I have printed it in both PLA and PETG looks like PLA is more then good enough, and holds up. The temp dosen`t deform the part. ...minimal support needed and it`s made to be a fast print.

Print with any film Print 50% or more infill

scale at 107% for larger bricks

A button for the cb radio Midland Alan 28 D

Printed With Standard Settings, I used PLA+ works great so far

-7

7