radrunner plus front rack 3d models

Mounting bracket for the Rad Power Headlight (Standard or Premium) to mount to the front rack. Allows for more clearance between the light and the front wheel/fender. It doesn't bounce around like the included bracket, and the tilt range is much...

Highlight your space with the Kartell Front Page Rack, a stylish and functional addition to any room. This innovative design enhances storage while adding a touch of elegance to your décor. ...Make the most of your living area by incorporating this...

I wanted to make a custom bracket to mount an LED area light that was recessed up between the Front Runner bed rack bars, but also angled out to illuminate the tailgate area. ...For my height, this is the perfect height and angle where I am not blinded...

Cable managing clips for solar panels, antenas or roof mounted lights on the Front Runner Slimline II roof-rack. The slat they are mounted on must be disassembled as they are inserted from either end of the profile. Because the base is square...

They can be used for a front rack. I designed a small box to hold her phone that uses these bolt holes. I also used the front facing surface to mount reflective tape to make her more visible at night. I mounted it on the biker's right side so it...

My next step is to design a bracket that will not only interlock sets of these paint racks but also enable them to be stacked together seamlessly. UPDATE: I've successfully created the first type of brackets, which are working wonderfully. ...However,...

This is the remix of the original roof rack: https://www.thingiverse.com/thing:4275052 I widened the screw holes, so now the screws can be mounted from the top. ... https://youtu.be/VizbeSLg2wc?t=123

move the board out of the way, and relocate the screws, foam surrounding the leds, along with the clear led diffusers. ...this revised model is designed specifically for rack mounting, where the connectors face forward.

FRONT panel: added holes for buzzer, RESET button and contrast dial BACK panel: added a hole for direct powewr supply over RAMPS connectors

You can see the customized version at this URL: http://www.thingiverse.com/thing:711518 and use it to customize again through this link: http://www.thingiverse.com/apps/customizer/run?thing_id=711518 Design Parameters Here are some specifications to...

I've created for everyone a roll bag bracket that is light, sturdy, and strong (all the things bikers care about ;)) In addition, it is designed to be printed vertically WITH NO SUPPORTS :D This front roll bag bracket can be affixed to the front of a...

There was plenty of vacant space under the rear rack of our RadRunner ebike, just begging to be utilized. Why not put it to good use and turn it into a storage area? I designed this drawer bracket in Tinkercad, and now you can too! Simply create your...

These are designed to work with the corresponding nut cover spacers and hold-down mounting bar to attach virtually any box or basket to the front rack on your RadWagon, RadExpand 5, RadRunner, RadCity, RadRover, or RadMini. The blocks are designed...

STLs Mount-Right-2x.stl (print 2) Mount-Left-2x.stl (print 2) Bracket-4x.stl (print 4) Knob-2x.stl (print 2) (All files are in correct Z-up orientation. ...**No supports needed**) Hardware For attaching mounts to the bike M6x40 bolt (8x) M6x30...

Decided to try to make 3D printed small running boards for the Rad Runner instead of making them out of aluminum + wood. Printed them with ToughPLA; first 10mm @ 80% infill, everything else @ 50% with 3 walls. My first try was with 25%...

### STLs - Mount-Right-2x.stl (print 2) - Mount-Left-2x.stl (print 2) - Bracket-4x.stl (print 4) - Knob-2x.stl (print 2) (*All files are in correct Z-up orientation. ...**No supports needed***) ### Hardware - For attaching mounts to the...

<p>Print in Carbon Fiber or other heat resistive material.</p>

<p>This throttle wraps around the Rad Runner's rotating throttle and is secured in place with an M3 screw. There are ridges to help the band bite into the rubber throttle, but you can add rubber pads or a strip of neoprene or dip the band in...

Mount crafted from high-quality PETG, coupled with a durable washer constructed from TPU. Printed at an incredibly precise resolution of 0.2. This design incorporates expertly integrated brass threaded inserts and reliable M3 socket cap screws for...

Customized version of https://www.thingiverse.com/thing:1957436 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1957436

For the case profile The distance from foot to head on the front of the calculator 187 mm (7.36 in) The curvature of the calculator side cross section Measured to be 10 mm (0.39 in). The curvature of the calculator foot front cross section. ...

It would be cool to see a TI calculator cover that had a hinge so the front cover folded open rather than coming entirely off.The key measurements include:For the rail/slot cross section profileThe distance from the calculator front keys to the to...

Mount the BUMM Lumotec Cyo to the top mounting holes of this Cube RFR front bicycle rack.

Now a days everybody seems to have a Plus after the name. ...So add a PLUS after your stuff.Print it in 3 colors.

Sonicmodell AR Wing Pro front Emax pan mount plus nose weight "add BB's" modified from b14ckyy design. ...19mm x 19mm cams.

Kugoo G2 Pro Swing Arm Cover Plus Front And Rear Fender This is a discounted group price for my Kugoo Parts. ... Check my other posts for other instructions.

A Basic Plus Sign Designing This Project I took a basic cube, stretched it out, and made it skinnier. A rectangle emerged, which I duplicated to create a cross. Then, I grouped it and completed the project. Project: Math! Objectives: Students will...