railcore github 3d models

This hack of a J Steve White stl enables three spools across a 300 mm wide RailCore by being screwed directly onto the 15mm rail. A hole is included for a filament guide, making it possible to print one standard and one mirrored version. ...This design...

Volcano Groovemount substitute for the RailCore II. Simply swap it in place of the standard v6 groovemount, ensuring that the nozzle tip remains approximately the same to maintain layer fan compatibility. Don't forget to adjust your Z-Probe offset...

This part allows you to use two toolboards to improve extruder modularity and wire management when using the aluminum dual direct drive extruder upgrade kit from Mandala Rose Works on the Railcore II 3d printer. ...It should be printed in a relatively...

| Part (Linked) | Description | |-----------------------------------------------------------------------|----------------------------------------| | [M3x5mm Brass Inserts](https://www.amazon.com/gp/product/B00Y20YLKY/) | Amazon/Uxcell version (6)...

This is a hack of a J Steve White stl to allow three spools across a 300 mm wide RailCore. It is screwed to the 15mm rail and includes a hole for a filament guide. Print one standard and one mirrored. It was specifically designed to allow me to do...

In order to print this case with the hex pattern pre-done print the railcore_paneldue_7i_case.3mf file. Other slicers may work but I tested this design with PrusaSlicer. Print instructionsBecause the hex pattern was done in slicer the original .scad...

Designed to work with the [NEMA23 stepper brackets from Mandala Rose Works](https://www.mandalaroseworks.com/product/railcore#nema23steppermounts). I used a 20mm M3 button-head bolt with a lock washer to fix the part to the printer. Without the...

Here are a few mounts to use on the Railcore system with a Nimble. Currently, there's a mount for the V6 and one for the Mosquito hot end available. If you need a different hot end mount, please let me know. Some holes appear to be blind holes,...

This is my E3D threaded heatsink for the Railcore using the volcano hotend. I printed with polycarbonate with carbon fiber, but any stiff material should do just fine. One thing to note, at least for me, to install this you have to remove your fan...

The purpose of this drill jig is to make it simple to drill an M3 hole on the edge of the new 713Maker magnetic bed for the Railcore 300ZL, 300ZLT & 250ZL. You would then tap and install a M3 x 8mm button head bolt with a M3 fender washer to act as a...

This mount allows you to use a Bondtech BMG on your Railcore II instead of the E3D Titan. It bolts on the same, with space for an optional brass insert in the Y carriage for added stability - drill a hole in your Y carriage and add a brass insert if...

Railcore II Y carriage for Dual extrusion using the Bondtech BMG-X2 EXTRUDER and E3D Chimera. 2x GDStime Technology 24V 0.1A 40mm blowers for cooling. I use a Omron E2B-M12KN08-WP-C1 2M inductive probe with this. ...Slight updates and all is...

I've created an adapter for ATX cable split boards on the back of Railcore II Titan Aero carriages by Empricus. It even has its own BL-Touch mounting point. The main goal is to eliminate all cables on top of the printer and achieve a flat, hidden...

Quick and dirty mount designed to secure the Dyze Design Filament Sentinel firmly to a Railcore 2 300ZL, a setup that will likely work seamlessly on any printer boasting 1515 extrusions. This mounting solution necessitates two M3x8mm screws and two...

These alignment pins are specifically designed for use with the Railcore II magnetic bed, MandalaRoseWorks Aluminum Z Yokes, and Thekkiinngg 300x300 powdercoated build plate. As the buildplate itself is not substantial enough/magnetic enough to...

This custom backplate secures the hinges of RailCore 2 doors. Initially, I was hesitant about tightening the nuts on the rear of the acrylic panels, trusting bolts within the material to withstand frequent door opening and closing. To alleviate these...

This is my precision-crafted E3D threaded heatsink tailored specifically for the Railcore using the volcano hotend. I utilized polycarbonate with carbon fiber, but any stiff material will yield impressive results. I've uploaded the step file and...

I figured I'd design a hermera (with Volcano hotend) mount for the railcore. All of the parts with inserts are designed to be used with M3 inserts with a 5.15mm OD (https://smile.amazon.com/gp/product/B077CJV3Z9). If you want to modify this design...

I updated the 302mm top interface component to feature a RailCore II logo and accommodate a 10mm waterproof LED strip in the back. There are also versions without the led notch that have the logo cut at varying depths. For the led version, the...

Steve White's hinges for the Railcore 2 ZL/T printers, serving as printable hardware for Acrylic doors designed by Mandala Rose Works. If you have 3mm (1/8") doors, print the 3mm hinge; if your doors measure 6mm (1/4"), use the 6mm hinge. The STL...

This is a mount for the Duet Magnetic filament monitor for the Hemera on a Railcore. The STLs are oriented for proper printing and should not require supports. Where supports are needed I added an integral supports (2) that need to be removed after...

This is a Door Handle for a Railcore II 300ZLT featuring a large single door. The goal was to implement a simple magnet/latch solution for the door. Utilizing parts that were readily available, this solution was devised. Parts required: 3 -...

The Railcore II Y carriage upgrade enables dual extrusion functionality, seamlessly integrating the Bondtech BMG-X2 EXTRUDER and E3D Chimera components. A pair of high-performance GDStime Technology 24V 0.1A 40mm blowers provides efficient cooling...

This is sized for the Mandala Rose Works Mosquito Mount, and the Railcore II print; it has clearance for the rounded front of the Alu mount, and it is short enough to keep the fan clear of the lefthand rails. The fan sits slightly higher than the...

This tool is designed for use with Railcore ZLT, even when yokes are flipped over; it will also work seamlessly with standard ZLT, as it doesn't require bearing holders. The intended print orientation is large side down, but both top and bottom...

This is a load spreader for the hinges of the RailCore 2 top cover backplate.\r\nI was not thrilled about tightening nuts on the back of acrylic and relying solely on bolts in acrylic to withstand constant opening and closing of the enclosure, so I...

Print Settings Printer: Railcore II ZL Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.14 Infill: 25 Filament: generic CF-PETG or PA black Notes: Try to print the base, top and cap in higher resolution; I used 0.14 The tension arms can...

Modified jstevewhite's cover interface for railcore to allow the use of a PC4-M10 push-fitting on the inside of the printer so filament could be fed from the outside.Print SettingsPrinter:Railcore 300ZLTRafts: NoSupports:Doesn't...

... with the Magnum pulleys. * Tentative confirmation of compatibility with the [713maker Halo](https://713maker.com/railcore/railcore-ii-300zl-halo) * Slight update to the usage instructions. ... 2019.03.17 --------------- * Initial publication

Once installed, the top is just a box with outside dimensions equal to your railcore, less than 7mm thick walls, making it suitable for 1/8", 3mm, 5mm, 1/4", 6mm, and other thicknesses that should work fine. And yes, I know there's debris in the...