railcore ii 300zlt 3d models

This is a handle and latch assembly for the Railcore II - 300ZLT. The printer comes with just a standard knob but no catch to hold the door closed. This assembly allows you to open/close the door as well as lock it shut. It is designed to be used...

cable clip for railcore II cables. ... remixed from thingiverse.com/thing:2812010

Side mount filament spool holder for the Railcore II 300ZLT. This fits existing holes. The hole in the top is sized for an 1/8" NPT tap to put an NPT tube holder fitting. I am sure other types could be adapted. Top two screws are 3x20mm button...

Parts print without support. ...You'll need to use CA glue to hold the parts together.

Parts print without support. ...You'll need to use CA glue to hold the parts together.

Filament Spool Holder for the Railcore II 300ZLT. Holders the spools under the electronics box. The spindle is a separate component so it can be replaced, modified, or altered without requiring the hanger portion to also be reprinted. ... Much...

This is a Door Handle for a Railcore II 300ZLT using a large single door. I wanted a simple magnet/latch solution for the door. Using the parts I had laying around I came up with this solution. Parts needed: 3 - M3x12mm Socket cap screws, a...

I had some cooling issues on my railcore II 300ZLT which were, according to my testing, caused by the location of the cooling duct. This mount replaces the 3d printed mount/adapter that comes with the railcore kits. It moves the entire cooling duct...

These are open-source doors for the Railcore 300ZL and Railcore 300ZLT. You (hopefully obviously) need 2 copies of the appropriately sized door for your machine, 4 hinges (2 parts each!), and 2 door pulls. The hinges are designed so that the side...

This is a complete file set to upgrade your Hotend on your Railcore 300ZL or 300ZLT to a Viral Inventions or 3DPassion Nova highflown Hotend. This is a premium, high flow precision Hotend. Similar to the size of a V6 but the volumetric flow of the...

There's a table at my site with all of the BOM's, Fusion 360 Models, Assembly Guides, etc: https://www.kraegar.com/railcoreii Gallery of sample prints: https://imgur.com/a/QNLli Facebook discussion group for RailCoreII builders & owners:...

Protect your table, print some snazzy TPU socks for your Railcore II! ... These fit snugly over the stock printed feet, no fixing required.

... surfaces. ... Use three standard Railcore II feet with this assembly in one corner, then set the height of the adjuster to allow the printer to sit level on an uneven surface. ... The optional TPU pad is designed to work with M3x8 countersink bolts.

A simple clip for the wiring bundle on the RailCore II, has a slot for a zip tie to insert. I used a 36" zip tie, and just cut the ends off. Inserted it in with my wiring bundle, and it keeps the bundle upright so it can't flop over. ...

Optional Printed Parts to upgrade a RailCore II to a RailCore IIZL The full RailCore II project is here: https://www.thingiverse.com/thing:2407174 The ZL option implements 3 point automatic bed leveling - physically leveling the bed using your Z...

Simple logo test print for the RailCore 300ZL.

This spool holder is a remix of a remix of a remix :) Its for the Railcore II printer. It requires a short length of M6x100 threaded rod and 4 M6x100 nuts. Use two nuts to secure the rod into the spool arm (alternatively you can thread in a...

... weight. Do not try to hang a 3.5kg roll from regular filament holder as it might break. Empiricus@Dremomys Print Settings Printer: Railcore 2 Rafts: NoSupports: Yes Resolution: 0.200mm Filament: Atomic Filament PETG Category: 3D Printer Parts

Filament holder for Railcore 2 300ZL and some brackets. No support in the post required. Added brackets and base for left side holder. New right side base and support to better deal with 3.5kg rolls. Ad spool holder thing:2431785. This holder has a...

I rebuild it from scratch but closely followed the Railcore V6 Part cooling Duct design by Hangtight . I also shifted the "horns" for use with a boot on the Mosquito Hotend. I suggest printing it at a 45deg angle upsidedown. (as oriented in...

Mount for the E3D threaded coldend for the v6 for the RailCore II

Case for the paneldue 5i. ...Mounting is for the Railcore II

I designed a squash ball foot mod for the RailCore II 300ZL based off the original files. Note: Squash ball will feel a little tight when putting them into the feet, just squeeze and rotate. ... Amazon: 4 x Squash Balls used - https://is.gd/uO36Vd

I designed a squash ball foot mod for the RailCore II 300ZL based off the original files. Note: Squash ball will feel a little tight when putting them into the feet, just squeeze and rotate. ... Amazon: 4 x Squash Balls used - https://is.gd/uO36Vd

RailCore® II 300 ZL/ZLTRailcore is a family of Core-XY based Reprap 3D printers designed by J. ...Steve White, Tony Akens, and Ben Withem.Build of MaterialsA BOM is provided with links to where you can source the parts and available aluminum...

This is a fan mount and blower for the Railcore II that is equipped with the aluminum ultralight Y plate. If offers a large spread out air wave for part cooling and nozzle tip cooling. No supports are needed. 5015 style blower fits snug so no...

I designed a squash ball foot mod for the RailCore II 300ZL based on the original files. Note: Squash ball will feel a little tight when putting them into the feet, just squeeze and rotate. Amazon: 4 x Squash Balls used - https://amzn.to/2zoOtWK...

However because I haven't had a chance to make the model fully responsive (Fusion isn't great about variants), if you do make the change be sure toadjust the centerline back to =13.7 before exporting the motor side as the hole location moves as well...

[Drag Chain Fusion 360 Files available](https://gallery.autodesk.com/projects/139518/railcore-ii-drag-chain) **BOM** | Part (linked) | Description | |-----------------------------------------------------------------------...

UPDATE: I highly recommend this thing by @Moriquendi instead: https://www.thingiverse.com/thing:2957477 This is the first go at making a mounting solution for the Precision Piezo Orion for the RailCore II. This is a work in progress, for sure, and...