ram mount for kenwood d710 and ram ht holder 3d models

I had purchased and installed a RAM mounting system for my car. The type that bolts to your seat. I used it for my DSTAR HT. I decided that I wanted to mount my D710 there instead. I found http://www.thingiverse.com/thing:220963 on TV and it worked...

... the clamping force better. This is printed in PLA, but I may need to print it in ABS if the car heat impacts it. Ram Mount publishes their dimensions, so I was able to replicate the exact dimensions of the shaft, ramp, and ball diameter exactly.

Adapter to go from a RAM mount to Kenwood TM-D710 remote head. ...Mic Clip is on the bottom and is inverted.

http://www.thingiverse.com/apps/customizer/run?thing_id=322859 Tested it on my D710 and it fits Instructions Using the following options: cross_tolerance = 0.5 phone_height = 130 phone_width = 70 grip_width = 3 flex_ridges = 1 cross_grips = 1...

Slip on bracket for the Kenwood D710 with 1" RAM compatible ball mount.

I'll test for usability soon. ... Instructions Using the following options: cross_side = 1 cross_tolerance = 0.5 phone_height = 130 flex_ridges = 1 head_diameter = 10 clip_width = 20 bolt_spacing = 48...

Just a super quick, super simple mount for the RAM mount diamond plate 1" ball, though I think the 2" diamond plate ball is the same dimensions so it should also work. You can view/download the cad file for this model here: https://a360.co/2TjlLgU...

I wanted an inverse of Ozy's ram mount, because the ball socket on my setup is positioned such that I want it closer. ... Rather than rebuild the entire socket system, I just put a socket on it.

September 2020 From: Randy - W4LKS Holder for Kenwood TH-D74 handheld ham radio designed to attach to a RAM mount to allow mounting on handlebars, dashboard, windshield, etc. Requires a RAM diamond base like this one:...

RAM yoke mount, fits 9.7" IPAD with DUNNO hardcover case After print, use adhesive velco for IPAD stay in place Recommend print in PETG or ABS (PLA will melt in direct sunlight). ... CLICK LIKE

First iteration of a ram mount compatible I made for the kenwood TH-D72 as there were none available I really liked. Notes: - Made to be used with the factory belt clip, it holds it in nice and snug - I have not yet tested this so may still need...

Combined a belt clip vent mount for a handhelt (HT) ham radio with the Ram B ball base.

Same as my other item but the ball is printed in plastic. ... This one works fine for me as I'm not in a Jeep off-roading. ... If you need a higher strength item, use the other one.

Cup holder ram mount

Mic holder to Ram Mount adaptor

Replacement for backplate of car holder for Zumo 660, to enable screwing it to a RAM mount plate. Open car holder by removing 6 screws, losening clips. Remove backplate and replace by printed part. ... Printed with support, filament = PETG

I really like Ram Mount products; I think they're incredibly useful for temporarily or permanently mounting things, particularly in vehicles. Unfortunately they don't have a lot of good options for mounting radios, particularly handheld radios. So,...

Helloas a biker I have a RAM MOUNTS X Grip holder to keep my smartphone on my handlebar and use it as a GPS.This system is really the best I've tried but… in rainy conditions, I use a GIVI universal smartphone holder (S957B) which have a raincover...

Attachment part for a Ram Mount iPad Mini holder to hold the Apple Pencil along side the iPad for easier access in cockpit or vehicle usage. Two different lengths of pencil holder parts are included in two widths. the 9mm (larger) worked great on...

Uavionix Sentry Mini adapter, can also be used to mount Stradux to RAM mount. ... *CLICK LIKE*

This spacer would work for anything you want to add a RAM mount to as long as it's big enough to glue. Instructions Insert one nut into each hole then glue to the back of the cradle, nut-side down....

... ... Made it customizable so that you can adjust it to other bikes as well Works with the stems in this thing: https://www.thingiverse.com/thing:1286674 For the case itself you might want to look at: https://www.thingiverse.com/thing:2359417

I added a latching groove and a cutout for your finger to release the latch...similar to the original Kenwood control head mount. The latch groove mates with the latch mechanism on the control head. This helps to hold the head more securely. I...

I decided to redo it utilizing Ram Mount's RAM-B-238 http://www.rammount.com/CatalogResults/PartDetails/tabid/63/partid/082065077045066045050051056085/Default.aspx . This allowed for much more strength. ...

this a drawer for the Rack05 of https://www.thingiverse.com/thing:1773329/files

This is a bracket designed to install Kenwood TM D710 mobile ham radiocommand panel in a Fiat Punto Street (2011) with minor mods. The bracket allows regulation of tilt and pan of the panel in order to have the correct wiev of the screen from both...

Adapts the supplied mounting bracket with a Kenwood D710G faceplate to a standard 1" ball, part #RAM-B-238 This does not require threading screws into the face-plate unit itself. You will need M4 fasteners longer than the ones supplied with the...

Needed a faceplate mount that fit closer to the ProClip base in order to clear the gear selector.

This is a 22mm handlebar mount for RAM universal phone holder.

Replacement feet for the Ram Mount Cell Holder Best printed in TPU or flexible material for best results and maximum hold