ramps 1 4 fan pin 3d models

1235035 3d models found related to ramps 1 4 fan pin.
Fan holder Ramps 1.4
Fan holder Ramps 1.4
thingiverse

A minimal fan holder for ramps 1.4 board complete it with 40mm fan, 2 exagonal 30mm spacer and 4 screw Instructions print with 100%infill

ramps 1.4 fan mount
ramps 1.4 fan mount
thingiverse

Holder for two 40 mm fans on Ramps 1.4 Instructions When testing the board found that the chips are heated by radiators drivers, and as a result decided to make them for cooling airflow. This taped secured on long M3 studs above the board. Material...

Ramps 1.4 50mm Fan
Ramps 1.4 50mm Fan
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: bracket_thickness = 3.0 bracket_length = 12 bracket_height = 36 screw_diameter = 3.25 pcb_width = 60.0 cross_bracket = 10 fan_hole_spacing = 40...

Fan mount ramps 1.4
Fan mount ramps 1.4
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: pcb_width = 60.0 bracket_length = 12 bracket_height = 36 bracket_thickness = 3.0 screw_diameter = 3.25 fan_size = 40 fan_hole_spacing = 32...

120mm fan Support for RAMPS 1.4
120mm fan Support for RAMPS 1.4
thingiverse

A support for 120mm fan for RAMPS 1.4. ...

120mm fan Support for RAMPS 1.4
120mm fan Support for RAMPS 1.4
cults3d

A support for 120mm fan for RAMPS 1.4.

RAMPS 1.4 Fan Mount 50 mm
RAMPS 1.4 Fan Mount 50 mm
thingiverse

50 mm fan mount for RAMPS 1.4

Ramps 1.4 universal fan holder
Ramps 1.4 universal fan holder
thingiverse

Universal fan mount for Ramps 1.4. ...The best fan mount to cool down stepper drivers.

RAMPS 1.4 Enclosure with 120mm fan
RAMPS 1.4 Enclosure with 120mm fan
thingiverse

... 3 mm screws respectively. I use heatset threaded inserts because they work and are easy to install. Note on your RAMPS You must replace the power connector with solder leads to the new external 4-pin power receptacles or the ATX power receptacle.

Fan extender for RAMPS 1.4
Fan extender for RAMPS 1.4
thingiverse

... down the printing head. To do this, in Marlin software, edit configuration_adv.h like this : #define EXTRUDER_0_AUTO_FAN_PIN 4 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50 #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed and reprogram the firmware.

Anycubic Delta + RAMPS 1.4 + Fan 60mm
Anycubic Delta + RAMPS 1.4 + Fan 60mm
thingiverse

Arduino mega + RAMPS 1.4 adapter for anycubic delta. Suitable for delta and delta plus. 60x60x25mm cooling fan. ...Arduino and ramps are positioned laterally both for a matter of space and for better heat dissipation.

Ramps 1.4 80mm Fan Mount
Ramps 1.4 80mm Fan Mount
myminifactory

This is a fan mount that clips on the Ramps 1.4 board, holds really well to the ramps board. ... Best printed at 0.2mm layer heigh and 50% infill

Dual Fan Ramps 1.4 cooler
Dual Fan Ramps 1.4 cooler
thingiverse

Dual Fan Holder for Ramps 1.4 Cooling Simple mounting system with side bracket that allows you to leave space and accessibility for cabling.

Ramps 1.4 enclosure lid_50mm fan
Ramps 1.4 enclosure lid_50mm fan
thingiverse

This is the lid for spauda01's ramps 1.4 enclosure for Vslot, i modified it so that it incorporated a 50mm fan instead of 60mm. ... I also added a hole in the lid for the graphic lcd connectors

Ramps 1.4 60mm Fan Mount
Ramps 1.4 60mm Fan Mount
thingiverse

Ramps 1.4 60mm Fan Mount Customized version of http://www.thingiverse.com/thing:166045 Instructions Using the following options: fan_hole_spacing = 50 bracket_height = 36 fan_size = 60 cross_bracket = 5 bracket_length = 12 screw_diameter = 3.15...

RAMPS 1.4 fan mount 40mm
RAMPS 1.4 fan mount 40mm
thingiverse

Fits 40 mm fan with bolt spacing 35 mm (1.4") outside to outside. Three improvements have been added. Nut trap on the inside, small skirt to channel air, and increased depth to not interfere the stepper wires, Instructions Use any RAMPS mounts (not...

RAMPS 1.4 Fan Mount Adapter
RAMPS 1.4 Fan Mount Adapter
thingiverse

Combine this part with two of these (http://www.thingiverse.com/thing:49235) previously designed parts to support a 40mm fan that fits a RAMPS 1.4 Board. ... I printed mine with .5 nozzle, ABS filament, .4 layer height and no supports.

ramps 1.4 enclosure 40mm fan
ramps 1.4 enclosure 40mm fan
thingiverse

Enclosure for the ramps 1.4 board with a opening for display cables. The box snaps together no screws needed except the 40mm fan mounts on the top of the box. Seen in photo is a 80mm fan because I ran out of 40 mm fans. You can use the base that sets...

40mm fan support ramps 1.4
40mm fan support ramps 1.4
thingiverse

Basado en http://www.thingiverse.com/thing:49235, soporte más elevado para dar cabida a un disipador mayor de los mosfet en mi ramps 1.4

RAMPS 1.4 Board Cooling Fan Mount
RAMPS 1.4 Board Cooling Fan Mount
thingiverse

Post-Printing Required Steps Parts: 2 (or 4 if you're ambitious) - M5x18 cap head bolts 3 - 20mm pieces of 1.75 or 3mm plastic 1.) To get the fan mounted to the frame just use the cap head bolts to screw the mount into the fan. I had to do some...

Ramps 1.4 box with 60mm fan
Ramps 1.4 box with 60mm fan
thingiverse

Box for holding ramps 1.4 electronics with a 60mm cooling fan. Instructions First thing I've ever made. Designed in sketchup. Sorry haven't made the jump to real CAD software yet. Make sure the...

RAMPS 1.4 Fan Mount, 40mm, parametrizable
RAMPS 1.4 Fan Mount, 40mm, parametrizable
thingiverse

A simple and small mount for a fan on a RAMPS1.4 board. The photos show a small 40mm fan, however the brackets are parametrizable and other fan dimensions (e.g. 50mm) could be used easily. The brackets have a small air guide on one side. I found some...

Ramps 1.4 50mm Fan Bracket
Ramps 1.4 50mm Fan Bracket
thingiverse

Neat fan bracket to keep your Ramps and probably other electronics cool. Simply drill and screw to your frame Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.4 Infill: 20 Notes: Supports are...

RAMPS 1.4 Fan mount 60mm
RAMPS 1.4 Fan mount 60mm
thingiverse

This is a simple symmetric bracket that mounts on the RAMPS shield. No screws required to attach the bracket to the board. ...Fits 60 mm fan with bolt spacing 50 mm center to center.

Ramps 1.4 Dual Fan Mount
Ramps 1.4 Dual Fan Mount
thingiverse

Remix of https://www.thingiverse.com/thing:145946/ I wanted a dual 40mm fan mount in 1 piece with fan guard.

80 mm fan mount ramps 1.4
80 mm fan mount ramps 1.4
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: fan_hole_spacing = 71.50 screw_diameter = 4.25 pcb_width = 60.0 cross_bracket = 10 bracket_thickness = 4.0 bracket_length = 12 bracket_height =...

50mm fan for RAMPS 1.4
50mm fan for RAMPS 1.4
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: screw_diameter = 3.25 bracket_length = 12 cross_bracket = 10 bracket_thickness = 4 fan_size = 50 bracket_height = 36 pcb_width = 60.0...

Ramps 1.4 with 80mm Fan Mount
Ramps 1.4 with 80mm Fan Mount
thingiverse

I always thought bigger is always better and no one had a design with the 80mm fan and a box so I made one! I made it on blender and included the .blend file if you want to modify it! Instructions...

80mm fan mount for RAMPS 1.4
80mm fan mount for RAMPS 1.4
thingiverse

Fan mount and protection shield to keep the cold flow away from the heating bed.

Ramps 1.4 120mm Fan Holder
Ramps 1.4 120mm Fan Holder
thingiverse

Since I only had one 40mm fan, which is quite cheap and loud and I have 120mm fans around, I decided to cool my board and especially the TMC2130 drivers with a 120mm fan. ... This holder works as is, but to save filament and time I cut it in the slicer...