raspberry pi 3 heatsink 3d models
788286 3d models found related to raspberry pi 3 heatsink.thingiverse
Just a simple remix with cutouts to allow for heatsinks to come through. UPDATE: I replaced the file with the correct orientation. ...Holes were flipped.
prusaprinters
Just a simple remix with cutouts to allow for heatsinks to come through. UPDATE: I replaced the file with the correct orientation. ...Holes were flipped.</p> Category: Electronics
prusaprinters
Just a simple remix with cutouts to allow for heatsinks to come through. UPDATE: I replaced the file with the correct orientation. ...Holes were flipped.</p> Category: Electronics
thingiverse
A remix of dfoles minimalistic Raspberry 3 A+ case top (with camera and GPIO pin slots) with an additional cutout for a cpu heatsink.
cults3d
A remix of dfoles minimalistic Raspberry 3 A+ case top (with camera and GPIO pin slots) with an additional cutout for a cpu heatsink.
cults3d
Slim case for the new Raspberry Pi 3! Case fits together with no mounting hardware. Remix Improvements: * Added cutout for a CPU heatsink since RPi3s run a little hot. I used the following 13mm x 18mm heatsink ->...
thingiverse
Slim case for the new Raspberry Pi 3! Case fits together with no mounting hardware. Remix Improvements: Added cutout for a CPU heatsink since RPi3s run a little hot. I used the following 13mm x 18mm heatsink ->...
thingiverse
... the PCB, which does not fit with the bottom heatsink. This design features one support for the bottom heatsink. Lastly, the fan mount was removed as the raspberry pi with a heatsink does not need a fan. ...A .prt file for NX is also inluded.
thingiverse
... ... I got the raspberry pi 3 kit from canakit, and it had a thicker heatsink. I adjusted this model to allow for that, as the original did not fit. ... Use the lid from https://www.thingiverse.com/thing:3023247 to finish it off.
thingiverse
Files : * Case\_Bottom_-_With_Vents_Small_Rods.stl is the original Case with small rods ; * Case\_Bottom_-_With_Vents_Small_Rods_MicroSD.stl is the same as above with a 3 x micro SD card holder. ... * Case_Top-Heatsink_Cutout_Only.stl is the original...
thingiverse
A large cooling solution for Raspberry Pi 3. I'm using one as CCTV for 2 USB camera with full HD video capture and the Pi get way to hot, causing it to throttle and ending up by a beautiful crash of the Raspberry Pi. I needed to cool it down, I have...
thingiverse
A simple case for the RPI 3B+ that has a cutout for a double fan cooling block.
thingiverse
I printed the case and sadly it did not fit/close because of a missing cutout for the 4 PoE-Pins. I kept the original files, so you can choose. The ones declared as ..."with_poe_hole" are the new ones. So I loaded it up und cutout the hole...
cults3d
Remixed from this one (https://www.thingiverse.com/thing:3026059) with the "roof" thinner to allow the fitting of Rpi with heatsinks. Printed with the SD Card side on the bed without supports. ... Note : use the cap from the original thing...
thingiverse
Remixed from [this one](https://www.thingiverse.com/thing:3026059) with the "roof" thinner to allow the fitting of Rpi with heatsinks. Printed with the SD Card side on the bed without supports. ... Note : use the cap from the [original...
thingiverse
(Sorry - Thingiverse is refusing to preview the model for some reason. The download still works!) I really liked the no screws case by jegi, but then I found the mountable remix by Walerian (https://www.thingiverse.com/thing:3616207). It's exactly...
thingiverse
This modifies [giacomo30196](https://www.thingiverse.com/giacomo30196)'s [Ender 3 Raspberry Pi 2/3 mount (UPDATED V2)](https://www.thingiverse.com/thing:3016364) rear/lower part to add a hole for a heatsink on the bottom of your Raspberry Pi. I had...
thingiverse
added some height to the case to allow for heatsink as not tested but old case would make it very close to the lid based on the stock heatsink you can buy, for the lid i made some holes where the heatsink should be so it can vent. ...Also changed bottom...
grabcad
An aluminum 15x15x15 mm heatsink for the Raspberry Pi 3 and 4 as sold by AdaFruit (#3082).Fusion 360 and STEP files
grabcad
Aluminum alloy heatsink for the Raspberry Pi Compute Module 4. Designed by Geekworm. ...Sold on AliExpress.
thingiverse
I really liked the original design by walter, but it his case did't fit my raspberry pi 3 with heatsink and did not have gpio access. So I decided to remix it. For the bottom part use the one provided by walter...
thingiverse
This is for the users of the Ender 3 Touchscreen Case & Holder for Raspberry Pi case but with a cutout for a heatsink. ...this provides more then cooling enough for the Pi, a fan is not needed
thingiverse
Remix of the Raspberry Pi 2/3 case top made by 0110-M-P ( https://www.thingiverse.com/thing:922740/#remixes) to allow for the heatsink i purchased with my Pi3 from adafruit to fit in the case. ...
grabcad
Raspberry pi 4 aluminium heatsink case, with 2 fans (25 x 25 mm).This model was created only for the purpose of being integrated in other projects.
prusaprinters
Simple Raspberry Pi with heatsink din rail adapter. Compatible with that passive heatsink nobody has a name for that's everywhere. ...You'll need 4x 2.5m 16mm to put it on.</p>
thingiverse
I needed a way to secure a Raspberry Pi 4 in [this heatsink case](https://core-electronics.com.au/pimoroni-aluminium-heatsink-case-for-raspberry-pi-4-black.html) since it's to be used in a mobile application, and has to be fixed to a panel. The...
grabcad
This is a model of popular cheap heatsink case for Raspberry Pi 4B. It was modeled by measuring heatsink I have with a caliper and I tried to reproduce it as precisely as possible. Only position of mounting holes was taken from the RPi specification....
thingiverse
Based on the design by Drew_B and using the dummy Rpi4 model by Olvin, I created this Raspberry PI 4 case to attach it to my Ender 3 v2 sides. It is designed to have minimal impact to air flow obstructing the massive aluminium heatsink, use minimal...