raspberry pi 4 case with battery 3d models

Case with slot to 2,5" disk.

The original case is here: https://www.thingiverse.com/thing:6158413 Where the top part of the case can be found, as there is an option for GPIO. This case slides into the mount and is retained by a push clip. The clip needs supports, most likely....

Added a hole in the case to access the GPIOs and added support for the Canakit fan without screws.

Everything is the same as the original; however, I added a slot for the onboard Pi camera ribbon cable to the top. ... It has enough room to easily manipulate the cable without creating friction.

... The step file is included if you want to modify it, be sure to retain sufficient holes for ventilation. If you opt to use it with the mounting bracket, you'll need 30mm M3 screws. I printed mine with a 0.4 nozzle and 0.15 layer thickness.

I modified the snapfit Pi4 case from 219Design. The modifications include making room for a M.2 SSD hard drive board, which can be found on Amazon here: https://www.amazon.com/gp/product/B01LZ0LCTU/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1. I...

The solution consists of a straightforward mounting plate equipped with standoffs to securely attach a 70mm fan, which happened to be the only one available at the moment. ...As a result, the Pi is running approximately 15 degrees Celsius cooler, thanks...

English: The fan mount should be glued with instant glue, the mount should be glued on the side with 6 ventilation holes. ... Español: Se debe pegar la montura para el ventilador con pegamento instantáneo, la montura debe ser pegada por el lado con 6...

I combined the 2Color version with the prior mentioned Thing, took the breakable slots into the second design, then shifted the Prusa text from interference area. That is all. Thanks to the two predecessors for their GOOD JOB! New in this version...

Modified version of https://www.thingiverse.com/thing:4901940

<p>Modified version of https://www.thingiverse.com/thing:4901940</p>

This is a lid for https://www.thingiverse.com/thing:3712178/remixes. ... I just dropped an 80mm fan on time.

Rough prototype of the Maker Focus Raspberry Pi 4 Battery Pack model, created as a reference while attempting to build a portable laptop using the Pi 4. This prototype helps visualize where cables and connectors need to be routed. ... The MakerFocus...

Although the documentation for Octoprint does not explicitly recommend the A model, it is quite capable of doing the job and requires less space than the B model.The Model consists of two main pieces that are held together when the case is mounted on...

This top is perfect for pairing with the mentioned bottom. The camera stand, on the other hand, is inspired by a design found at http://www.thingiverse.com/thing:256960. ...To create this item, Tinkercad was utilized and its online version can be...

Across all the great models of RPI mount, which are already placed here, I couldn't find a proper one for an RPI with the case I already bought. It works with the case shown in the pictures. You need to screw it into the two free M3 holes and click...

Remix of this awesome case http://www.thingiverse.com/thing:846874 with added ventilation. ...Thanks for the original upload lyratron!</p> Category: Computer

Pins durch Schraublöcher ersetzt. ...Der Raspberry hat leider nicht in die Pins gepasst, so dass ich das ursprüngliche Layout von jesse76 (https://www.thingiverse.com/thing:1573414) angepasst habe.

Case for model upgrade to best available solution.

... specifically with the ID #978990. ...My goal is to integrate an 8x8 LED matrix into the design of the top case, while also adjusting the standoff height. This will allow for a more immersive experience and better compatibility with various components.

I've updated the design with extended files at both the top and bottom because my original USB connector was too long, making it a tight fit inside the case. The case now features screw holes on either side, as well as protective covers to safeguard...

Heya! ... Just a modification for a 30mm fan in the amazing case from Malolo. Original case: https://www.thingiverse.com/thing:3719217 Happy Printing!

I took Manolo's basic case and added some customized venting. ...

I needed a Pi camera cover that could be mounted using simple M3 bolts, but couldn't find one. So, I designed and printed my own. The tolerances of the parts ensure they snap together easily when printed at fine settings, eliminating the need for...

It's exactly what I need - one that proudly displays the Raspberry logo. ...Here are my print settings: Printer Brand: RepRap Printer: Hephestos Prusa I3 Rafts: Yes Supports: No Resolution: 0.2 mm Infill: 30% Notes: I used a Brim because I...

Motion Eyes OS Base Case Design This base case design is specifically tailored for MotionEyesOS use. ... The STEP file accompanying this design allows users to freely modify its parameters.

... lid. I suggest nylock nuts. I used spare hardware I had left from my MINI+ spare hardware, so a couple bolts in the picture are longer than necessary.&nbsp;Posting your makes, leaving reviews, commenting with suggestions or requests is appreciated.

Simple case for RPi3B+ with extrusion rails for your 3D printer / laser cutter / milling machine etc. No screws needed. I included two versions: vent_ version ready for 4010 fan with vent holes on both sides infill_ version is supposed to be...

Sorry about that! Simple case for RPi3B+ with extrusion rails for your 3D printer / laser cutter / milling machine etc. No screws needed. I included two versions: vent_ version ready for 4010 fan with vent holes on both sides infill_ version is...

This RaspberryPi case is derived from Thingiverse's design (http://www.thingiverse.com/thing:16104) and developed in collaboration with Petteri Sillanpää as part of Devaamo's Hackday results. The instructions include a Blender model for the bottom...