raspberry pi 4 egpu 3d models

Screen case for Sunfounder Raspberry Pi 4 Display Touchscreen 7 Inch Case (HDMI & USB)

4 LEGGED ROBOT WITH RASPBERRY PI AND 12 \SERVO MOTOR , WITH CAMERAS AND SENSOR , 3D PRINTING ,

This is a remix of kwh32901's Pegboard Mounted Raspberry Pi B+/2/3 Sleeve, adding support for the Raspberry Pi 4. I opened the case up so that a Raspberry Pi 4 with heatsinks can slip in. I also expanded the HDMI opening so that there's room for the...

Explore Raspberry Pi modeling, an innovative approach for designing and creating projects using the versatile Raspberry Pi computer.

Case for Raspberry Pi 4 and Geekworm X862 SSD expansion board. Board has 1Tb M.2 ssd. ...Case sized for expansion board and raspberry pi and small pi cooling fan.

https://www.printables.com/model/271131-raspberry-pi-4-vesa-100-case Raspberry pi 4 case with vesa 100 mount I wanted a good raspberry pi 4 case with a vesa 100 mount, so remixed a base and a mount. ... Vesa base from...

Raspberry Pi 4 Case for RGB Cooling Hat Remix from [nimanouri's Raspberry Pi 4 Case](https://www.thingiverse.com/thing:4074096). This case supports Raspberry Pi 4 with RGB Cooling Hat, 4 12mm M2.5 Standoff are needed to mount the top case. ... Hardware...

This model is designed to attach to the Holybro x500 drone. ...On the top cover, you will find a CSI cutout and 2 holes designed for hanging a generic camera gimbal.

Square off the area around ports so could fit bigger cords.

Print or use to make new thingsLeave a like it really helpsIf you want me to make a certain model leave a comment below.

Remix of John_Sinclair's excellent model with slots on one long side and one short side instead of the rounded air vents. Also slightly reduced wall thickness from 2.5mm to 2mm. Picture shows the enclosure mounted on my printer. ... ...

Customized version of https://www.thingiverse.com/thing:4921568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4921568

Customized version of https://www.thingiverse.com/thing:4921568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4921568

Just litle bit higher top mesh case to fit in my 30x30x10 fan with high connector

Customized version of https://www.thingiverse.com/thing:4921568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4921568

Customized version of https://www.thingiverse.com/thing:4921568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4921568

Here's an update to this old design, and an apology for mixing things up so that it wasn't entirely right for a PI4.  I'm sincerely unsure what was going on that made me mix it up like that.Anyway, here's a new version that is definitely for the...

Rapid Prototype Case Design. Built to Snap Together Securely with M3 Screws. ...The Genius of M3 Holes Lies in Their Ability to Eliminate the Need for Supports Entirely.

I added screw tabs to the side of the case to allow it to be mounted. ...I also printed out standoff washers to use under the tabs to hold it away from the wall.

<p>Here's an update to this old design, and an apology for mixing things up so that it wasn't entirely right for a PI4. &nbsp;I'm sincerely unsure what was going on that made me mix it up like that.<br><br>Anyway, here's a new version that is...

Patent-Pending Lock Prevents Patio Umbrella Spinning Out of Control When Tilted to Block Sun's Intense Rays. Crafted specifically for 37mm umbrella poles, this ingenious lock is designed to keep your outdoor umbrella securely in place. While it may...

Rpi4 Case, no supports.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

-8 pcs M2 screw required. -Can be used without fan. -Fan is 30x30mm lenght. -Due to not to crack mounting holes the screws must be heated up before installing. ...

Customized version of https://www.thingiverse.com/thing:4921568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4921568

This model is designed to attach to the Holybro x500 drone. ...On the top cover, you will find a CSI cutout and 2 holes designed for hanging a generic camera gimbal.

<p>the building is SELF explanatory…</p>

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/9SO08dRXh1d