raspberry pi camera focus tool 3d models
242262 3d models found related to raspberry pi camera focus tool.thingiverse
I created this wrench to allow me to focus the camera while mounted in a bed-mounted camera holder. ... I use a Lulzbot bed-mounted camera holder with my Octopi setup, following this write-up:...
thingiverse
This tool lets you adjust the focus of a Raspberry PI zero mini camera.
thingiverse
I printed a camera case for the Raspberry Pi v2 and I needed a tool that I could use to focus the camera's lense without having to remove the case. This tool does just that, it prints relatively quickly and it will only cost you a penny in PLA! If...
prusaprinters
Printing Instructions: Resolution: 0.15Supports: NoRafts: NoAssembly Instructions: (Best to assemble on a flat surface.)Press fit Focus Bit through Gear B until it hits your table. Place the above assembly on to Shell A, align the...
thingiverse
I designed this focus ring that you can super glue to your raspberry pi camera. It allows you to easily focus the manual focus lens. IMPORTANT: Make sure you just put a bit of glue on the top of the pi camera lens on the outside (not near the lens...
thingiverse
I printed the Pi Camera (v1) Focus Tool, then I realized how small it was. I designed this part to hold the tool and ensure it doesn't get lost. The part also is perfect for holding mini shears. ... Pi Camera (v1) Focus Tool...
thingiverse
... a support blocker so that only the outer edge was supported. 3mf files provided for PrusaSlicer users. Fits this camera: https://thepihut.com/collections/raspberry-pi-camera/products/raspberry-pi-camera-adjustable-focus-5mp?variant=20063161843774
thingiverse
A simple case that I designed for the Raspberry Pi Camera Module V2 that holds the camera module itself in place to allow for the focus to be safely adjusted. ... If you find any design flaws in what I have so far, let me know and I'll work on fixing...
thingiverse
I needed to focus my Raspberry Pi camera but I'd already mounted it in an enclosure which prevented me from using one of the other numerous tools I'd already printed from here. So I designed a tool with a long neck so it could get inside the recessed...
thingiverse
Key for adjusting sharpness of Raspberry Pi cameras V1.3 original lenses. I didn't found the right model for my camera, so I made it myself. Clef pour ajuster la netteté des objectifs originaux des caméras V1.3 Raspberry Pi. Je n'ai pas trouvé le...
thingiverse
Took a modular mount for the PS Eye, and mixed it to fit the new Pi Cam with auto focus. Print the Base and Mount, then print arms as needed. Attaches with 2 M5 screws and T-slot nuts. ... Edit: V2 is slightly thicker for a better fit.
thingiverse
The original file did not fit the camera I have (too big). ...So I scaled it to 92% of the size and added another cylinder to interlock with the camera. This worked just fine for me. ...:) I had to remove the glue beforehand.
prusaprinters
After I replaced my stock camera module with Arducam IMX219 Auto Focus Camera Module, I found out that it can't fit in cover provided in Articulating Raspberry Pi Camera Mount. So I took its step file and aligned camera module hole by 1.464mm lower.
thingiverse
Hex screwdriver bit to adjust focus of raspberry pi camera v2.
grabcad
Hex screwdriver bit to adjust focus of raspberry pi camera v2.
thingiverse
This case is designed for Arducam IMX219 Auto Focus IR Sensitive (NoIR) Camera Module(https://bit.ly/38TFDhK) and IR Version(https://bit.ly/36tmzpG) This Arducam IMX219 camera module is designed mainly for the Raspberry Pi V2 camera board and NVIDIA...
thingiverse
This is a merge of my tool holder with a newly designed Raspberry Pi case and a built in camera holder. It doesn't require any screws to mount to the Tevo Tornado frame (I assume it will work with the CR-10 too but I don't have one so can't confirm)....
thingiverse
... CR10(s) and Tevo Tornado. Added a lid for the raspberry pi with "printed" air vent. Works with a raspberry pi 3 and most camera attachments. Designed using Autodesk Fusion 360. Enjoy! ... Check out our website at www.printedbournemouth.co.uk
thingiverse
Adjust the lens of an original Pi camera V1.3 This remix of Wurstkarton's remix of jpaul038's focus tool makes the cylinders fit the notches better and scales it back to 97%. For my camera this finally got the grip I needed to turn the lens even...
thingiverse
Simple, but effective, mount for the Raspberry Pi camera. It will fit on a lot of 3D printer beds (the "claw" is 10mm - 0.4in - wide). The mount is inclined so it can point to the printing area. It features a slot to pass the flat cable. ...Included are...
thingiverse
This is a remix based on https://www.thingiverse.com/thing:3114849 by https://www.thingiverse.com/sneaks. ... Goal was to enable an easy change of focus while using the exisiting mount system. ...