raspberry pi cm4io board 3d models
111294 3d models found related to raspberry pi cm4io board.thingiverse
This is a simple board mount for the Raspberry Pi. It has two screw tabs for fixing the mount to a board and the Pi is a push fit so you might need to scale up or down depending on how well calibrated your printer is. ...It is a remix of my...
thingiverse
... with this board design here: http://www.thingiverse.com/thing:566506 The original Sketchup file is included along with the STL. If you are looking for the Raspberry Pi B+ board, you can find it there: http://www.thingiverse.com/thing:402498 Enjoy.
thingiverse
... here, but still. You can also see the case I made with this board design here: http://www.thingiverse.com/thing:423216 If you are looking for the Raspberry Pi A+ board, you can find it there: http://www.thingiverse.com/thing:566520 Enjoy.
grabcad
Raspberry Pi GPIO Breakout board with pin header 2x20 pin male, 8.4 mm high
thingiverse
Experimental Board for Raspberry PI with SD Card holder Raspberry Pi is a trademark of the Raspberry Pi Foundation see: http://raspberrypi.org/ Instructions Experimental Board for Raspberry PI with Breadboard Holder, SD Card holder and box for...
thingiverse
... is a board accompanied by four pegs to create a modular Raspberry Pi cluster rack. ...The rack's minimalist design allows the user to access nearly the entire Raspberry Pi, while the peg holes allow the board to stack on top of other boards via pegs.
grabcad
Raspberry Pi Zero W board.New version with built-in WiFi and Bluetooth.Overall dimensions: 65mm x 30mmPorts: SD Card slot, mini HDMI, micro USB (x2), 2x20 (+4) female pins, CSi (camera) socket.Simplified model with all major components present. ...All...
thingiverse
This is a fitting/holder for the Raspberry Pi camera board. The board features two mounting holes to mount the holder on, for example, a paper clip, as well as a screw hole to fit it on something else using a screw. ...
thingiverse
Prototype board for Raspberry Pi. Frame Size is 180mm x 141mm x 7.2mm Parts MB-102 Solderless Breadboard 4off Rubber feet 12mm plus screws DC-DC Buck Converter Step Down Module LM2596 Power Supply 2.1mm Jack Socket WARNING Please Check the Power...
thingiverse
Currently working on a NAS case for a Raspberry Pi CM4. This model is a low poly to-scale model of the CM4 IO board for prototyping. As follows: IO_Board_Prototype.stl - just the IO board, no CM4 or heatsink and fan CM4+SINK+FAN30mm.stl - just the...
myminifactory
Instructions Just print it out, stick the bread board on and screw the pi on! ... The breadboard is this one: ...
thingiverse
Instructions Just print it out, stick the bread board on and screw the pi on! ... The breadboard is this one: http://www.ebay.com.au/itm/830-Tie-Point-Solderless-Breadboard-Protoboard-ZY-102-/121427221044?pt=LH_DefaultDomain_15&hash=item1c45a05a34
thingiverse
This is a placeholder/model for the Raspberry-Pi Zero, after the mechanical drawing on element14 NOTE: while the PCB itself is exact to the specification (including holes and rounded corners), the correct placement and size of the components is NOT...
thingiverse
You will need some screws or something like that (I used header pins with heat shrink over them) to screw the camera mount to the board clip. I may update it to eliminate the need for the screws in the future.It works well and still allows a bit of...
thingiverse
Raspberry pi case with dual relay board, also designed to screw into cr-10 control box.
thingiverse
Raspberry Pi 4 holder and cable clip for IKEA skådis peg board
grabcad
3D-printable Duet 3 mainboard (6HC) stand. ...Has smaller stand for raspberry pi underneath the Duet board.
thingiverse
The Raspberry Pi 4 case to fit the ReSpeaker board (4-Mic array). ... Designed for my RoboDog project.
grabcad
Raspberry Pi Compute Module 4 IO Board. ...Also included is the CM4 with eMMC, but without wifi or bluetooth.
cults3d
Mounting plate for Raspberry Pi 400 CYBERDECK Hat and 5cm x 7cm perfboard. Uses M2.5 fasteners and M2 fasteners for mounting the boards. ...Learn Guide coming soon.
thingiverse
Mounting plate for Raspberry Pi 400 CYBERDECK Hat and 5cm x 7cm perfboard. Uses M2.5 fasteners and M2 fasteners for mounting the boards. ...Learn Guide coming soon.
thingiverse
Vorpal Board that can be used with two PCA9685 boards and one Raspberry Pi. ... You can fit also a Lipo battery in the middle part of the PCA9685 boards.
thingiverse
It's just a basic holder for Raspberry pi CM4 IO board with a holder for PCIe card. ... Parts are press-fitted so you'll need a hammer or something to put it together.
thingiverse
Rumba board Box with Full Graphic Smart Controller and Raspberry Pi 3 Up Part for controller - remake this thing https://www.thingiverse.com/thing:516447 +Soliworks files for remixes
thingiverse
Just like the original but this one has two mounting holes for the revision B and onwards Raspberry Pi boards. The holes are 2.8mm in diameter which is sufficient for a M3 (3mm) bolt to self-tap a thread. I used two M3x8 hex headed bolts. ... The holes...