raspberry pi ender 3 3d models

... the fan friction fits snugly between the board and case so they're not necessary. There are mounting pegs for the pi at the back, you'll also want to get a right angle adapter for your pi power supply as the cable will not fit going straight down.

I added top perforation for air flow, space for 40mm fan, I used Sunon MF40100V1-1000U-A99 40x40x10. ...Left the bottom part fan hole for cable routing.

This is a revised remix of the original remix by Codemonkey1973, specifically designed to eliminate any remaining lettering from the flat surface.

Flatter pivot part so it's easier to print with ABS. Bigger contact patch so there is more friction and less likely to pivot inadvertently. ...Print with no supports, but with bridging on.

Remix from the `upperpart_V2_30mm.stl` file without any other holes than the fan one.

To reduce plastic waste accumulation within the case, minimizing port openings was essential. ...Additionally, opting for LM2596 mounts sans fan was a key consideration.

The Arducam Auto Focus camera I picked up didn't fit into the mounting plate, so I threw together one that did. ...This is the camera in question: https://www.amazon.com/dp/B07SN8GYGD

https://www.kiwi-electronics.nl/tweekanaals-relais-module-5v?search=relais&description=true https://www.kiwi-electronics.nl/kw-2274?search=Step&description=true https://www.kiwi-electronics.nl/rocker-switch-spst-round?search=swi&description=true

I modified this design to work with the BL Touch 2mm Extension Satsana Duct designed for the Micro Swiss Full Metal Hot end. ... For use with this fan shroud specifically https://www.thingiverse.com/thing:4689712

The original design used M3 screws for the case which required tapping the RPi board. I modified the bosses to use M2.5 screws instead, so no changes need to be made to to RPi board. Also modified the fan mounts to use M3 screws, and added a hole...

i extended the arm for about + 50mm to go out of the way when you use a HeroGen5 Head and BLTouch

I wanted to use this (4721088) but on the right side like this (3781016) and could not find it so I cut and stitch some. ... Will probably need to file a bit the bracket as it did not fit on the camera case quite well.

Print "standing" like you see on the cura picture (with build plate supports and brim only). ... UPDATE: V2 supports the camera (cable)

I found the mount in Krypto088's pack for the picam didnt seem to work with the picam2. ...I redid it to make the threaded mount match to Stingr's picam mount but with Krypto088 threading since I had already printed it.

A remix of a remix of the camera arm from https://www.thingiverse.com/thing:4721088. This arm has been extended to prevent it from being hit by the left Blower duct of the Hero Me Gen5 and gives clearance for a BLTouch. ...

Installed adaptable interface connectors, and cord receptacles, borrowed directly from a reliable online resource at thingiverse.com, specifically the design with ID 3256773.

... believe it's compatible with most printers. ...To get started, you'll need a USB cable that's at least 40 cm long, along with some M3 nuts and bolts. If you also happen to have a Biqu Thunder or a Raspberry Pi 3A, be sure to check out my other designs.

Reimagined Solution for Mounting Electronics on the Left Side of TeachingTech's Ender 3 All-in-One, Optimized for the Raspberry Pi 3A+

... SKR 1.4 (Turbo) 4 x LM2596 Buck Converters (https://www.amazon.ca/dp/B08Q2YKJ6Q? ... psc=1&ref=ppx_yo2ov_dt_b_product_details) Raspberry Pi 3B for octoprint This is a REMIX of the VF Ender 3 MAX Front Electronics Box, Board/Pi/Bucks by vinceformosa

Another project proposed a case for the Raspberry Pi 3 that can be easily snapped onto the Ender 3 rails without requiring any screws: https://www.thingiverse.com/thing:3008866. ...By incorporating the mount system from the second project into the...

- [Improved Ender-3 V2 Replacement Drawer for Raspberry Pi](https://www.thingiverse.com/thing:4656072) - Only replaces the removable drawer instead of the entire enclosure and exposes the pi ports on the front of the printer - [Raspberry Pi...

I personally used one from rs components as they have quiet 24v ones https://americas.rsdelivers.com/product/rs-pro/od4010-24lb/rs-pro-24-v-dc-dc-axial-fan-40-x-40-x-10mm-85m-h/1442036 This is a remix of two Ender 3 electronics cases:...

I personally used one from rs components as they have quiet 24v ones https://americas.rsdelivers.com/product/rs-pro/od4010-24lb/rs-pro-24-v-dc-dc-axial-fan-40-x-40-x-10mm-85m-h/1442036 This is a remix of two Ender 3 electronics cases:...

______ Remix aus dem Raspberry Pi 3B+ case (3, 2 & B+ also fit) von dktosoch und einem Cabel Clip den ich leider nicht mehr im Original auf Thingiverse finde (solltet ihr das Original kennen, schreibt mich bitte an und ich nehme diese mit auf). Das...

For S1 Pro only. ...The rest parts for this mount you can find here > https://www.printables.com/model/3407-articulating-raspberry-pi-camera-mount-for-prusa-m

Ender 5 screen rear cover W/O RPI 3 Case

When installing be careful to not clip over your wires.Printed with PETG with 100% Infill using PrusaSlicer.Remix of:https://www.thingiverse.com/thing:5365986/files...

(I`ll use a L angled USB cable connect straight to raspberry pi - https://www.aliexpress.com/item/33008052765.html?spm=a2g0s.9042311.0.0.e4564c4dXVB8Po ); I`m using TFT35 E3, so I don`t need those connections; ----------- I`m still working on the...

Remix for this model:Ender 3 s1 pro mountYou can use this piece to add an articulating system to your ender 3 s1 pro, I personally use it for mounting an articulating arm with a camera on top.A filet for the holes so it's easier to print, video also...

I also like mount which is perfect for my needs, I have it attached to my ender 3 v2 and it fits perfectly. I just needed to add a fan and a better slot for the camera ribbon cable. I can't find the other thing I remixed but took the fan cut out and...