raspberry pi for car stereo 3d models

Hi all, I designed this to make a console for Klipper. ... I used 3x10 mm screws for case and 2,5mm for pi. Front_back panel is designed to hold the display but also for display board in mai case. I will add small updates special for power. ...

This wallmount for Raspberry (3 and 4) which have a common heat sink case. A small roof protects from dust. The mount can be attached with two screws. ... To release the RPi again from the mount: Lift it and push it a bit to the side and it will...

UPDATED (2022-11-1) DINRAIL mount for the Raspberry 4 board v01.1 designed to use M2.5 or M3 heat inserts from Ruthex to fix the PCB firmly to DINRAIL mountv02 designed to use >2.1mm self tapping screws to fix the PCB firmly to DINRAIL mount.

RainBerry3 is a compact, rugged case that safeguards Raspberry Pi 3 and Raspberry Pi2 versions, plus the Pi Camera, within a single weatherproof enclosure. Equipped with O-ring seals, it can be mounted anywhere at any angle using a swivel mount. ...This...

Replace the lid of your Buddy Board with this drop-in case for your pi.Compatible with the standard and filament sensor cable covers.Although I have been running this for a while, without overheating, good heat syncs or a small fan is...

This small print accessory swiftly attaches to USB ports, elevating the Pi camera. For a stronger grip, apply hot glue around the mount's interior. Four holes align with the camera, accommodating screws without nuts. ...Trim excess tabs for better...

This is a simple mount for the Aokin Raspberry Pi Camera Module 5MP 1080p OV5647. The camera module is 25mm x 25mm x 1mm and has the ribbon coming out of the bottom. The mount slides onto the standard Raspberry Pi .1in pitch 40pin header. I use a...

Installing a fan directly above the Pi case is an excellent idea, which I successfully implemented by carefully drilling tiny openings into the top surface and securely fastening them to the fan beneath. ...This setup allows for efficient airflow and...

... model with a 1.00mm nozzle with 15% infill. I didn't like the idea of mounting the Canakit down because I like ease of access, and the ability to remove the pi whenever I need it for something other than 3d Printing, and this solves that issue.

Design by me based on te Terra Pi. ...For the assembly i used some carbon standoffs, but any material will do. I also included some standoffs which require m3 bolts in various lengths. To mount the ssd i used M3x6 screws. ... Enjoy!

I redesigned this raspi cam holder because I needed one that allows the camera to be removed quickly and easily, giving me the opportunity to take out the top table of the IKEA Lack Enclosure for maintenance purposes since my pi is located underneath...

I Use Double-Sided Tape to Secure Ribbon Cables This lets you keep your Raspberry Pi camera's cable or any ribbon cable securely fastened to a surface using 19 mm double-sided tape. I utilize it to route the cable along my Printrbot Simple's bed...

... cable. It must be passed through the hole and plugged in before inserting the raspberry Pi into the case. I freed up some space inside so that it passes without problem. ... Print this version with the same position and parameters as the original

It should work with a standard flat raspberry pi camera cable. You have to just slightly bow the cable to get both ends in and then it just slides into the slot and flattens out. Easy peasy. I also added the source file in case you want to...

Expansions to the raspberry leaves logo provide ample room for showcasing the PiGlow, and careful widening of the GPIO opening on one side ensures seamless compatibility with the edge of the PiGlow board. ...Furthermore, removable feet have been...

Holder can be Glued or double sided taped to the pi case

I mashed up the Rpi tray with some clamps I'm already using for my RAMPS board on the opposite side of the printer. I also added a bridge underneath the SD card as I have to wedge something against my SD card to boot the PI. ...UPDATE: I added a lid...

These brackets take the hardware from the Sensecap M1 or other Raspbery Pi based project and mount them in the Extreme Broadband external enclosure. There are two brackets, one normal one and one with an offset mounting hole to accommodate the...

... to it to protect the camera ribbon. Since installing it requires removing the ribbon from either the camera or the pi to thread it through the chain, I haven't done that yet, but I will be doing it shortly when I finish printing my current projects.

Pi Camera mount for the prusa xl, it is mounted to the left side of the CoreXY gentry.It will just pushed onto the frame without any bolds or screws. ...The camera case and base I used this model...

I've engineered a heat-dissipation module specifically tailored for Raspberry Pi, featuring a 30mm fan to ensure efficient airflow. The design is meticulously crafted to accommodate a 5-inch LCD display from Waveshare, providing seamless integration...

... two piece bracket to hold a microswitch. &nbsp;The microswitch can be programmed to shut down the server when pressed. See https://github.com/TonyLHansen/raspberry-pi-safe-off-switch/ for details on wiring and programming this feature. ...&nbsp;</p>

To install the Pi, angle it so as to engage the audio jack and hdmi sockets first then press the Pi down on to the 4x standoffs on the case bottom. 4x 8x3mm High silicone self adhesive feet stop the case sliding around. I used supports for the...

 Note:  I used the Canakit from Amazon and you will need to not use the large heat sink for clearance and also remove the metal fan pins from the black housings so it clears. ... Here is the kit that was ordered:...

Remix of the awesome Raspberry Cam v2 mount for MK3S(+). When printed for the MKS3+ the camera position was a too low.Thanks to @fuchsr for providing the step file, I was able to modify the mount a little to adjust the camera arm angle to have the...

I haven't tested any other models. Additional Parts:     2 M3 screws (not too long otherwise they may collide with the extuder) Assembly:Attach the bottom of the case with the screws as shown in the picturePlace the Raspberry in the caseClose it with...

... making it easier to route the cables through the system. For cooling purposes, I selected a fan from the thingiverse project titled "thing:255873", which offered a robust design that would efficiently manage the temperature within the system.

If you're looking for added security, I recommend using longer screws and nuts, such as 2mmx12mm with nuts for standard cases or backs with built-in connectors, or 2mmx16mm with nuts for add-on connectors. This project is ongoing, but the current...

This is a modification of the case that is featured here: https://www.thingiverse.com/thing:2832531 I have added a slot for the header pins, a hole to view the power status of the LifePO4wered board from above, removed the fan attachment points and...

Print it so the prusa is upside down with support on build plate, I used PETG with 20% infill.The pi and case i used is from amazon https://www.amazon.com/gp/product/B07XTRK8D4/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&amp;psc=1 I love that it gives...