raspberry pi housing 3d models
129817 3d models found related to raspberry pi housing.thingiverse
A remix from Philmacflys / flazers raspberry pi housing. NOTE: the gap for the LEDs has been closed on purpose, if you want to see them you need to print this thingi using a translucent filament! ... there are is no opening for cables (cam,...
thingiverse
Case for Raspberry PI from 2 to 4 with enough space to enclose heatsink with fan or special Power HAT https://www.tindie.com/products/18818/ Required screws: 4x - M2x25 4x - M3x5 Required nuts: 4x - M2
thingiverse
Ender 3 Pro Screen+Raspberry pi housing. ...Coupled together with my simple cable tie mount it works wonderfully: https://www.thingiverse.com/thing:4094437
thingiverse
after i did that i inseted a third card but the same happened, where the sd slot is about 12mm inside the box its very hard, even with tweezers despite it go in they still went poof, this was with 2 raspberry pi's so i ended up getting this which...
prusaprinters
Housing for a Raspberry Pi that mounts to the Frame of a Prusa MK3 for the use of Octoprint.(Fits for model 2 and 3, not RPi4!)You will find a Camera Mount for the Pi-Camera...
thingiverse
A housing for the Raspberry Pi Model B board with space to mount the camera board including a camera hole. The camera is screwed into the top part of the housing with 4 M2 screws. These can be screwed directly into the holes, no tapping required. I...
prusaprinters
Raspberry pi 3B+ Housing with brackets for rail mounting on Prusa i3 MK3.The bracket fits in the frame rails and can be mounted on either side of the printer. The idea for the slot mount is from this print:...
thingiverse
Housing for mounting a PanelDue 7i to a Troodon, with a Raspberry Pi mounted inside (with cooling fan). Ideal for Klipper upgrades. ... HOUSING, CONTROL PANELDUE 7i Part #11061-B Associated components: Part #11062 BRACKET, UPPER, HOUSING, CONTROL...
thingiverse
UPDATED to v1.2 04/29/17 A simple two piece, easy printing, easy assembling housing for a Raspberry Pi with a 120mm fan mount above it. Pi 3's run quite hot, and this housing provides plenty of cooling performance as it is open air, has perforation...
prusaprinters
Notable changes in the design are the fan placement and size, I have modeled a fan tray of sorts that mounts after the installation of the Pi and is secured with a T-slot nut. The fan mount is for a 30x30mm fan like the ones that typically come with...
thingiverse
The fan mount is for a 30x30mm fan like the ones that typically come with Raspberry Pi cases is also slightly adjustable to center airflow over the processor or clearance (should it be required) for buck converters. ...(this is why there is a space...
thingiverse
I modified my original housing to occupy a IR receiver for our raspbmc media center. So here it is There is also a version with a "IR tower" I never printed it becuase I decided it to be not so practical. I've included the thing file too, including...
thingiverse
Remixed the top part of Esquilos nice Raspberry Pi housing (thanks a lot for this cool thing!) in order to fit a Adafruit Radio Bonnet connected to a Raspberry Pi. Please use the bottom part from Esquilos thing. See here:...
thingiverse
I used the lost space on the Creality Ender-3 printer to add a raspberry pi housing and a drawer to put the tools. ... You can see it in "action" in this video: https://www.youtube.com/watch?v=FV9_XtL8wQ0
thingiverse
I remixed the "Backlight holder for Anycubic i3 Mega" by iceekb, added the Raspberry Pi Housing by Bogdanko's "Led Holder V.2 for Anycubic i3 Mega" and made a camera housing with party from jonprogers "Anycubic i3 Mega Pi zeroW camera mount". You...
prusaprinters
Remixed the top part of Esquilos nice Raspberry Pi housing https://www.thingiverse.com/thing:1637227 (thanks a lot for this cool thing!) in order to fit a Adafruit Radio Bonnet connected to a Raspberry Pi.Please use the bottom part from Esquilos...
grabcad
An unfinished demo model that illustrates how to create complex, compound surfaces without using lofting or surfacing tools. This model needs screw bosses and connector/ port details worked out. I will upload a finished, 3D printable version if I...
thingiverse
Adjustable housing for a Raspberry Pi display with Pi Camera holder. ... The parts are assembled with M3-.50 X16 pan head machine screws and nuts.
thingiverse
This is a simple housing for a Raspberry Pi Camera. #4 screws are used to mount it rigidly to a surface. The camera is surrounded/protected by plastic. The design fits my v2.1 camera and probably the others as well. ...It's OpenSCAD, so you can tweak...
thingiverse
Case for Raspberry PI 160° camera. ... The hole for mounting has a diameter of 40mm.
prusaprinters
This is a housing for the Arducam OV5647 camera for the Raspberry Pi. It also fits the Raspberry Pi camera V2.1, and other cameras with a similar format. The camera should easily fit into the back part and the front attaches with a friction fit. ...You...
thingiverse
This is a housing built for the Raspberry Pi v2. It has a hole at the top to allow for a ribbon cable to be attached to the expansion pins on the board. You'd need small self-tapping 2mm screws to close the box. Print both parts with the outside...
prusaprinters
This is a simple housing for a Raspberry Pi Camera. #4 screws are used to mount it rigidly to a surface. The camera is surrounded/protected by plastic. The design fits my v2.1 camera and probably the others as well. It's OpenSCAD, so you can tweak...
thingiverse
A housing for Raspberry Pi 3 which has about 25mm of additional space for your own electronics. It consist of two parts which are screwed together. The bottom part has a mountig for a 1/4" nut to mount the housing on top of a tripod. The housing is...
thingiverse
The second version of R.Pi camera housing is smaller with 9 LEDs and possibility to adjust camera angle.
thingiverse
A simple snap fit housing for the Raspberry v1.3 and v2.1 cameras. ... 2018-10-09: Made minor changes so that the v2.1 camera fits better.
prusaprinters
This is a snap-fit housing for Raspberry Pi Camera (rev 1.3) integrating 5mm LEDs. It is meant to be a smiling face - if you get the first layer setup properly.</p><p>All the cases available rely on the use of screws for closing the case. So I made...
thingiverse
This will lift the case about 1.5mm up so that the bottom has sufficient airflow for the chip on the bottom of the pi. For most application I do not think a fan is necessary so I took the liberty to adapt a second top with a pi logo. I printed it in...
thingiverse
Falls jemand das gleiche Raspberry Pi Gehäuse hat wie ich: https://amzn.to/2VuIWUf und einen Adapter zur Wandmontage sucht, hier ist er ;) ------------------------------------------------------------------------------------------- English: In case...