raspberry pi playstation 2 3d models

... Worth mentioning is that on this specific Pi board, the mounting holes measure precisely 2.8mm - nearly seven-sixty-fourths of an inch - rather than three millimeters exactly. ...Thus, a gentle drilling out was needed to secure it snugly in place.

I needed a stand for a Pi Zero and a time lapse. Two of these did the job. ...

... printer calibrated). I've included my Simplify3D supports file for the case. PLA, sliced with Simplify3D, 2 perimeters, 3 top/bottom solid layers, 20% infill, supports as shown in the pic. ...The cap was printed with 2 perimeter and solid infill.

To install the Pi into the main part, place the cover onto the PI and slide it into the main - it snaps into place. No screws are needed except for adding the 40mm fans if you add the cooling layer. These parts need to be printed with supports: *...

By request, a replica of a playstation 2 memory card. ...It has space inside for business cards, but this requires scaling up the model.

This case takes a 4010 fan no screws are required. For PWM this has screwless slots (2x) for the PWM module which you can get here at Amazon.Fan I used is Orion 4010 5v 2-pin fan. ...I am running it via a 3.3V pin on Pi for lower noise.The TOP and...

Here's the text that the Human entered: Simple case design based on the pi 2 model by Lyratron. Custom Section Notice to Mariners The inside dimensions on this part need to be correct. In the design I left a .5mm gap around...

Just the cam arm (without the Pi Zero case) from the WIP thing: https://www.thingiverse.com/thing:2781897 by DanTexasMan (Female mount version)

Just the cam arm (without the Pi Zero case) from the WIP thing: https://www.thingiverse.com/thing:2781897 by DanTexasMan (Male mount)

Made this to slide onto the tray for remote viewing of my printer. ...Screw mounts for Pi Camera plus a "friction" mount for the resin tray.

fully ventilated housing for pi zero and zero 2w July 30, 2022 new base file update: 5v and usb symbol reversed to match power port

The result exceeded my expectations: * The build volume remains unchanged, with the holder mounted 1 or 2mm below the carriage level * Compactness is achieved through a mere 2-degree tilt * Four 12mm magnets secure it in place and facilitate easy...

This is a super quick tinkercad remix of the pi zero frame from Prusa Research that relocates the support post to an empty spot on the PCB and raises the frame above the mini hdmi port which appears to be slightly taller than on the original pi zero...

I was thrilled with how my print of Vinjegaard's case turned out, so I decided to create another for my other Pi 3 model that I'm using in a separate project. ...This particular Pi 3 is attached to a piece of wood using two screws, so I reinforced the...

This is a super quick tinkercad remix of the pi zero frame from Prusa Research that relocates the support post to an empty spot on the PCB and raises the frame above the mini hdmi port which appears to be slightly taller than on the original pi zero...

Made Caddys for: Raspberry Pis (90 degree cable needed for ports on the side) 2.5 inch hdds usind ugreen sata to usb 3 A Adapters(The smallest/cheapest I could find) 2x PiZero optimised for POE-hat use. (Very high, clears only without IO-Pins,...

Pi Zero 2W heatsink slot is larger and slightly more to the right. UPDATE: Modified the .stl for more clearance when mounting to the 2020 rails. It was originally a pretty tight fit. ...After this update, it should slide in a bit more...

I removed the name etched into this decent pi case, allowing it to be printed in T-glass without displaying someone else's name. ...Check out the original for the top-rated options.

Check out this cam arm, stripped of its Pi Zero case, which is part of a work-in-progress project. View it on Thingiverse here: https://www.thingiverse.com/thing:2781897 by DanTexasMan. ... (Female mount)

A camera holder designed specifically for the pi camera version 2.1 is also included in this mount. When printing the parts, a layer height of .12 or finer is recommended to ensure smooth and precise results. It's worth noting that no supports are...

Print Settings Printer: T-MAX 2.0 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: Printed in: * Bottom: BuMat Blue 1.75mm ABS * Top: Inland White 1.75mm PETG ##### Job specs - Cura: * 0.6mm nozzle * 0.4mm initial layer, 0.2mm successive...

I was searching for a Pi case that could easily attach to my CR-10 without any hassle. Unfortunately, none of the cases I came across met my expectations. I decided to take matters into my own hands and modify Adrian12's case by adding some custom...

I simply repositioned the Pi and LED openings slightly, allowing for sufficient space to install a Micro-USB slot directly in front for powering the Raspi. To achieve this, I merely inserted a 15cm micro-USB female-to-male extension cord into the...

I have designed a custom mount for a modified PI case from Hackoholic, specifically tailored to fit snugly onto the aluminium extrusions of the Prusa MK3 in front left position. This mount can be easily detached by simply clipping it out. The PI...

Thanks again to Gael_Langevin for his incredible project at inmoov.fr and www.thingiverse.com/thing:67676! ...This remix is designed to accommodate a Raspberry Cam on the right eye, and I achieved this using only some simple double-sided tape.

First of all , thanks one more time to Gael_Langevin for his awesome proyect http://inmoov.fr/ http://www.thingiverse.com/thing:67676 This is a remix to fit a raspberry cam on the right eye. ...I added useing just some double side tape.

Rapiro Neck Modification for Raspberry Pi B+, Raspberry Pi 2 B Based on original designs found at Thingiverse and Rapiro wiki, a modified version is created to fit Raspberry Pi B+ and Raspberry Pi 2 B instead of the standard PiB.

This remix adds support for a voltage regulator so that the Pi can be powered off of the Ultimakers input voltage, as well as a slightly adjusted holder for the relay so that it would fit mine. I've attached the OpenSCAD file that I used to make my...

This remix enables power supply via a voltage regulator, allowing the Pi to run on the Ultimaker's input voltage. Additionally, an adjusted relay holder is included for a secure fit. ...An OpenSCAD file has been attached to facilitate future...

I was looking for a Pi case that could easily mount to my CR-10. Nothing I found I liked. I used Adrian12' case and added a couple of mounting brackets to it. I think this will work out just fine. ... Thanks, Adrian12 for a very nice case.