raspberry pi rack mount thingiverse 3d models

... lens like the e.g. ...https://nl.aliexpress.com/item/1005004549580517.html . Next to that my module has the FPC connector on the same side as the lens, so I moved the slotted hole. Rest of the design from: https://www.thingiverse.com/thing:3147295

Remix of the outstanding design by https://www.thingiverse.com/Xangal/about, tailored with minor adjustments to suit my setup perfectly, since I was encountering problems with obstructed views during the initial layers. ... Reduced the arm length by...

This is a reimagined version of the Camera Body from LazaroFilm's design found on Thingiverse under the ID 3030107. ...The goal is to perfectly match my RPi Cam module from Sertronics, ensuring the cable connections align properly when connected from...

I combined the non-movable parts of the original model (https://www.thingiverse.com/thing:2722833) into a single part because they didn't hold up well when printed individually at my location. ... This entire thing prints out well with the sphere...

This is a remix of https://www.thingiverse.com/thing:1718628 I modified it so that I could use an existing frame screw in my twotrees sapphire plus printer. My camera was deeper so I had to modify the front case to fit it and also the pins were a bit...

This is another RaspiCam case mount design for Anet A8. This one use the heated support to fix the cam with two heated arms : One to be only on the sides One to be on the side and on the front The heated arm slide on Anet A8 heated support and fix...

I don't own a raspberry pi zero but pretty sure the mounting holes are the exact same. M3 sized holes. I did not need any nuts, as it screwed right into the plastic. Has a cutout for GPIO pins. ...Does not include a top as I have a heatsink...

Place your Raspberry Pi in the base, followed by mounting the LCD plate on top. Securely snap the top section onto the case. Finally, attach the bracelet to the bottom clips; super glue might be needed for a tighter fit. ...The case's channel can...

Pictured in the first photo, are also a Raspberry Pi Zero W ultraSlim mount, found here: https://www.thingiverse.com/thing:2504847 and GoPro Mount arms & base found here: https://www.thingiverse.com/thing:2194278 This model is a slight remix of a...

You need the rack from: https://www.thingiverse.com/thing:4886186 This version is for the raspberry pi 4 with mounted joy-it cooler. It's 6mm higher. It's need 2 longer screws for mounting. ... Print Settings: Print face down No supports needed .2...

This is a simple mount for the Aokin Raspberry Pi Camera Module 5MP 1080p OV5647. The camera module is 25mm x 25mm x 1mm and has the ribbon coming out of the bottom. The mount slides onto the standard Raspberry Pi .1in pitch 40pin header. I use a...

Raspberry pi

I wanted a camera mount for my pi-cam so I designed this with magnets in the base so I didn't need to modify my chassis. required materials: 4x small thread-forming screws. M3 I think. I don't know. 3x 10mm diameter x at least 1.5mm thick...

I had a small issue with my raspberry pi cable being too short to get a decent angle for my printer, so I made a quick draw-up in Fusion to bind the cases together. I tweaked the case to fit my pi with a heatsink and an io port I also added a...

You need the rack from: https://www.printables.com/de/model/69176-1u-raspberry-pi-rack-with-moduler-traysThis version is for the raspberry pi 4 with mounted joy-it cooler. ...It's 6mm higher.It's need 2 longer screws for mounting.Print Settings:Print...

Liked the minimalist of this case for the 3b+ but wanted it to rack mount. Later decided I wanted to add a fan to it since I had to remove some area for the heat sink. ...Fan sits over the mounts and is screwed down with M2 cap head screws

Remix from https://www.thingiverse.com/thing:3001109 I needed a Pi3 case to be 1U rack mountable and can fit a 3mm LED power indicator light as well as a 15mm power switch on the front panel. ... Included the stl without LED and power switch holes.

... was using the smaller 25mm fan. ...Also I noticed that the mount was blocking the Pi cam ribbon cable. I also hollowed out the stands because the screws I used were pretty short, so printing with supports is needed. ... Supports: yes Resolution: 0.2

 However, the Pi Plate provided for a good reference/starting point (sized right for the Pi4, standoffs already in place and sized appropriately for the Pi4 screws, etc.).Squared off and solidified the plate itself, added chamfering to the Pi...

Another mount for Ender 3 Raspberry Pi Camera Mount (https://www.thingiverse.com/thing:3188580). ... This thing fix the camera on the Y mount axe.

This is Raspberry Pi camera mount... Print instructionsCategory: 3D Printer Accessories Summary This is Raspberry Pi camera mount for this holder: https://www.thingiverse.com/thing:2818559 Remixed from https://www.thingiverse.com/thing:2833311

I required a mount for both my RPi3 and Camera simultaneously. Not finding anything suitable, I devised this solution myself. The result works exceptionally well for me. It was printed in a single, seamless piece. However, it necessitates careful...

I needed a mount for both my RPi3 and my Camera. Did not find anything sutable, so I came up with this. Works really great for me. Printed in one single peace. Need some careful handling to get the hinges released after it's been printed. ... Bolt on...

Another mount for the Ender 3 Raspberry Pi Camera Mount is now available, courtesy of Thingiverse's 3188580 entry. ...This innovative design fixes the camera firmly in place on the Y axis mount.

Mounting Plate Hole Size: 4mm Raspberry Pi Mounting Peg Holes: 2.05mm Compatibility List: This mounting plate is designed for use with the following Raspberry Pi models: * Raspberry Pi 2 Model B * Raspberry Pi 3 Model B * Raspberry Pi 3 Model B+ *...

Raspberry rack mount project in progress, description later

This is a flat front ball mount that can be used with the Articulating Raspberry Pi Camera Mount (https://www.thingiverse.com/thing:3114849) It's perfect for mounting a customized camera housing on it, like this one:...

This is a unique Raspberry Pi camera mount designed to fit snugly into the provided holder, which can be accessed at https://www.thingiverse.com/thing:2818559. ...This design has been expertly remixed from the original concept found at...

Raspberry Pi 3B/3B+ Two case options: Option 1: Mount the raspberry with the top facing outwards and the bottom facing the wall. Option 2: Reverse the position, with the top of the raspberry facing the wall. Photos show option 2. Four M2.5 screws...

Explore Raspberry Pi modeling, an innovative approach for designing and creating projects using the versatile Raspberry Pi computer.