ratchet strap 3d models
22890 3d models found related to ratchet strap.thingiverse
I stumbled upon a glowstick holder for 25mm straps here on thingiverse, printed it, but my glowsticks didn't hold. So i made my own. I listed the original as remix-source. Please check it out, it might suit your needs better, depending on the size...
prusaprinters
Pull the end of the belt (25mm, typically found on shoulder straps of backpacks) with the thicker part pointing towards the adjuster through the stopper and close the latch while pulling the stopper downwards, so it closes more easily/firmly. ...Lift...
thingiverse
This is an adapter for 3rd party straps to make the strap more compact and comfortable. ...It raises the strap by a few cm and allows for it to compact down a lot better.
thingiverse
Install on the lower elastic straps of a mask to increase convenience in installation and removal of mask. ... Use with half-inch elastic straps, or cut-down a wider strap to 1/2" (~13mm).
cgtrader
Brass Strapped Table Lamp by N/A | 3d model produced by Design Connected | www.designconnected.com This 3d model is part of the highly acclaimed Design Connected collection featuring 6500+ carefully picked exclusive furnishings. Check out our full...
myminifactory
Attach your goPro to your vest, bag or other strapping using this molle clip
thingiverse
To get the sides all tight with the smallest amount of gap between them, try using a small ratchet strap on top of the rubber bands. I printed one that used paracord as the strap. After the glue has dried, put the knob in the center hole on the top...
thingiverse
A magnetic base to secure bundling straps for cable management. ... Slide the velcro like strap in-between the slits on the base to secure your cables. ... The magnets used are N42 Neodymium Disc Magnets; 3/8" x 1/10".
thingiverse
Usual face masks like dust masks or surgical masks have too long head straps to be worn by kids normally. ...This clips just saves the hassle of trying to knot the straps together.
cults3d
A magnetic base to secure bundling straps for cable management. ... Slide the velcro like strap in-between the slits on the base to secure your cables. ... The magnets used are N42 Neodymium Disc Magnets; 3/8" x 1/10".
thingiverse
STL for printing replacement key for lock on spa cover straps or other items that have a "Nexus Lock".
thingiverse
Strong if you use PLA at 100% fill.These are straps for 3/4" and 1/2" PVC pipe.
cults3d
This Tensioner for tension straps is in scale 1/10 for Crawler. ... Use 4mm or 5mm bands
thingiverse
I had some expired N95 masks with rotted straps - and I really like the adjustability and comfort of the 3M half-mask respirator straps. So I created some parts that I can retrofit to my expired N95 masks to work just like the 3M half-mask respirator...
thingiverse
... of the Nintendo Switch. ... It can handle a joy-con grip and 2 joy-con straps without taking too much space. Rails for the joy-con grip and straps have a nice fit, so you don't need to force on your joy-con nor your straps to get it in place.
thingiverse
... to make a viable head strap out of pla. I don't recommend printing this. Side straps remixed to print on a ender 3 rest of the parts are at https://www.thingiverse.com/thing:4651120 Updates Nov 21, 2020 - fixed side strap thickness design flaw.
thingiverse
I took the model, added a slit for the lower strap so that the Knuckle Strap will secure the Touch controller to the handle. Pretty secure if you run the top strap around the sensor ring and pull it tight. ...I also included my test print that is just...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=95636 Instructions Using the following options: mw_length = 100 text_position_side1 = 10 side2_image = magic_wallet20130602-1516-9c98yn-0.dat print = straps mw_strap_small = 15 text_font =...
thingiverse
I have modified a strap design made by a friend so that it can fit with the original "Easy 3D printed Face Shield" Thanks to HanochH (original Face shield) and Thanks to Nico Renoult (original design of the straps) In order to easily attach the two...
pinshape
Summary I've always thought these clamps are cool for some reason, and I'm also working on a customizable version. The design is a little tricky though since the circles are all "unwrapped" when in the neutral position. Anyway, have fun with my scan...
myminifactory
This is a simple clamp for holding bundles of wires, cables, or even pneumatic hose. ...Edit: Here is a modified version by 'robkingva' which allows you to snap the parts together!
thingiverse
Print without supports. Can be printed using PLA. Print with three walls and 25% infill. After printing, the hinge may be fused. Gently push the clip closed near the hinge to break it free. If you can't break it free, use the Customizer to...
thingiverse
Overall the same function but I lost the original files so I used tinkercad to remix this to: reduce its size, strengthen the sections where it failed before, resize the holes so a 3mm-dia x 10mm-Long screw can clear one and drive...
prusaprinters
<p>Looking to hang up my slide belts, the print here was too big for my Prusa Mini so I chopped 50mm of each side and rotated it 45 degrees to make it fit. ...Printed excellent and works great.<br> </p>
youmagine
I printed in abs at 20% rectilinear infill but I set every 5th layer to print solid for added rigidity.Be aware that one of the parts is oriented upside down in the model, so if you print it as provided then you are trying to make a cantilever over...
thingiverse
I've made a minor adjustment to the great capo design from LoboCNC to facilitate a rubber band, which should improve string contact and noise dampening. ... All credits to LoboCNC for his original design, this is just a minor tweak.
grabcad
This project was created to use in instructional rendering for pool equipment plumbing.
pinshape
This is a simple clamp for holding bundles of wires, cables, or even pneumatic hose. Edit: Here is a modified version by 'robkingva' which allows you to snap the parts together! ...http://www.thingiverse.com/thing:715328
thingiverse
This is a simple clamp for holding bundles of wires, cables, or even pneumatic hose. It works using the inherent flexibility of plastic parts. Works in PLA or ABS. Inspired by traditional cable clamps like this one: https://amzn.to/2HLJeTN Update:...
thingiverse
A little two-piece shoelace tensioning device! Wind the knob to tighten your shoes quickly, press the lever to release them! It's fast, easy, cheap, and secure! ...Hope you enjoy it!