ratrig 3d models

<p>The hinge is held together by some M3 bolt at least 22mm long.</p><p>You need a Pi camera ribbon cable of about 500mm.</p><p>Remixed from:</p><p><a...

!NEW! ...Version: https://www.printables.com/model/288965-new-v-minion-drag-chain-assembly-v2-zx Updated version of ZX JUNCTION (V2) that mounts to the X motor cage rather than the X axis extrusion, you will need included X_motor_cage_V2.

<p>Modular cable spines for wiring the electronics panel of your Rat Rig V-Core 3. They are connected using 1x m6x12. ...They are larger then the original Rat Rig cable spines to allow for more/thicker cables.</p>

<p>This is the regular V-Core 3 rear motor mount with a sealing lip and minor adjustments.</p><p>The sealing lip is on top of the bottom panel and therefore both seals and additionally underpins the motor mount.</p><p>It is designed for a 3mm bottom...

This is a shround used on EVA3 with BTT Knomi v2.

<p>LED holder for flexibel LED-Strips from BTF-Lightning.&nbsp;</p><p>I bought the leds here: <a...

<p>Basic cover to protect from accidental touching of the mains input. ...Just use t nuts to fasten.&nbsp;</p>

<p>First off all you need a angled USB-C cable for the pi. ...(see picture) and 3mm heatset inserts, all parts are put together with Screws</p>

<h5>(SEE Z-AXIS DRAG-CHAIN ASSEMBLY FOR OTHER FILES)</h5><h5><strong>Updated version of ZX JUNCTION (V2) that mounts to the X motor cage rather than the X axis extrusion, you will need included X_motor_cage_V2</strong>.</h5><h5><img...

<p>If there are problems with Z Wobble when using ballscrews, here is a 100% solution for it. Extremely simple, cheap and space-saving solution. Eliminates 100% of any Z wobble if present, no backlash and easy to swap.</p><p>&nbsp;</p><p>Fits Vcore...

<p>Designed to fit the new enclosure 2.0, on a Vcore 300.<br><br>I made this to stop my cats from reaching the wires from the side. ...should print well in any material since its basically a flat panel</p><p>Includes two version of the bottom right...

<p>Based on the original CAD from <a href="https://github.com/nionio6915/Euclid_Probe/blob/main/CAD/Rat-Rig%20V-Core/EuclidDockVCore3_3030_V5.stp">https://github.com/nionio6915/Euclid_Probe</a></p><p>Please note that according to the CAD model this...

Uses the same hole spacing as the floor panel. ...Mounts to the left of the rear rail.

This LCD case is heavily inspired in beef76's thing, so I consider it a remix. Thank you beef76 for sharing it. The screws needed are: 6x M3x12, 4x M4X12 and 2 M6x35. The nuts needed are: 4x M4 and 2x M6. The LCD is this one:...

<p>Remix of the original cable mount, since pulling a thick shielded cable for the ACC sensor put too much strain on the original mount. Mounts from 2 planes to the 3030 extrusion. ...Not the cleanest remix, but it works</p>

Spool holder for 2 Kg fillaments

You will need8x M3 Brass heatstake inserts - short M3x5x46x M3x8 Countersink screws (for the magnets)2x M3x10 Cap head screws (for the bed cable relief)This mod will give you bed arms a nice and clean look and you don't have to worry about dropped...

I wanted a screen mount that could double as a pendant. This is meant to swivel out of the way when not in use and can also rotate for the best viewing angle. It will also open up mounting options. I personally use it most as a pendant when working...

Pretty self-explanatory I would think :) Use M6x12 hex screws and washers

made it just for fun

Here are the remixed parts to use Gates toothed and smooth idlers. For my setup, the belt spacing got a bit bigger due to the Gates parts being slightly higher. You'll also need a collection of small and large washers - I printed them in ABS and...

I ended up using a normal microswitch for my X Endstop (only two wires needed in the umbilical) and the stock endstop block was a bit too low. ... This is a slightly (3mm) taller version and whilst at it, I increased the width & thickness of the slot...

Finally, wobble rings arrive on the V-Core Pro 1.3 :) I got a lot of inspration from the design from cnccyborg, thanks a lot! The aim of wobble rings is to eliminate perimeter artifacts which are caused by horizontal movement on the leadscrew...

This is a latch designed for holding 3mm thick acrylic panels to 3030 extrusions. This is basically the design found on the Voron 1.8 electronics covers, but slightly modified to better fit 3030 extrusions. Use double sided tape to hold the clips...

<p>When building my V-Core 3.1 I had trouble attempting to keep the X-Y 3030 extrusions square with each other while tightening the brackets down. I designed this square to be clamped to both extrusions and then the bolts be tightened in the brackets...

This is EVA mount for BONDTECH LGX FF extruder Please print from PET-G I have tested it up to 200mm/sec with 5000 acceleration and for me it is stiff enough. ... Please print all published parts to have whole construction stiff (those parts had been...

<p>Spool holder with bearing for T-Slot 3030</p><p>&nbsp;</p><p>What do you need?</p><p>1x spool_holder_m5.stl (3 perimeters and ≥20% infill)</p><p>4x bearing_shaft.stl (3 perimeters and 100% infill)</p><p>4x bearing_block.stl (3 perimeters and 100%...

Hello! I was searching for a perfect cable chain to complement my V-Core Pro setup, but unfortunately, nothing caught my eye. I'm aiming to route the bed cable precisely in the middle of the back plate, right into the electronics box. It works...