razor and brush holder 3d models

A handy safety razor and brush holder. Wall mounted. You can use some double sided tape, command strips or whatever you like to stick it to the wall. ... Update: v3 stl file is rotated so the flat surface should lie on the print bed by default

a razor and shaving brush holder V2 a space saving done on 360° merger

I made a model of a razor and brush stand with a soap dish

This stand will hold a standard double edge razor and most shaving brushes.

When you don't have much space over the sink, and you're always wondering where to leave your brush to dry- Features a bonus blade holder on the back! Currently fits a Maggard double edged / three piece safety razor kit with a 22mm synthetic brush.

The first try at a base stand worked, but was too light and fell over easily. Version 2 & 3 have a cup at the bottom. Add heavy stuff there (coins, rocks, whatever). I don't like to print with supports if it can be avoided. So, I used a handy...

Holder for my Safety Razor and Proraso Shave Brush. ...The Proraso shave brush handle is larger than most so I had to make this so it could dry properly.

This is a standard Brush and razor holder. I designed it to hold my Merkur. The new Gillette handle is too wide but an old Mach 3 handle should fit fine. It stands roughly 5" tall and is 2" wide. I printed it with PLA and it did great. I used support...

I had issues with the original being a bit flimsy and plain looking so I added structural supports and customized it for my Omega brush that has a square handle along with giving the edges a more rounded profile as the original was quite sharp. ...I DID...

... the wonderful original design, simply added a few ribs for strength. ... My brush and Qshave razor were enough weight to begin sagging the top plate. Also added a version with larger rib supports. ... Print like the original, no supports needed.

Holder for shaving brush, safety razor, and two packs of blades. ... Print Settings Printer: Anet A8 Rafts: No ...

Wall holder for a razor and a brush. ...I made it in two parts so I can change only one of them if I buy a new razor or brush.

A suction cup holder for a razor and shaving brush Instructions The assembly comes in two parts: Top holder (67x41x15.78mm) Stem Suction cup connector (68x26x8mm) The magnet is 20mm in diameter; a smaller magnet can be used. The suction cup connecter...

A handy bathroom razor and toothbrush holder. ... i printed this in black PLA I it took 8 hours to print you many need to do some adjusting Thanks for downloading my model, please give it some likes and comments.

... all have the same half moon shape on the back, so this should be able to mount to any of them. Designed in Luxembourg using Fusion 360. Cross-posted on [Cults](https://cults3d.com/en/3d-model/home/razor-and-shaving-brush-holder-for-ikea-tisken).

This is a custom-designed bathroom/shower accessory that can hold a standard-sized razor, a mini razor, and a shaving brush. The shaving brush holder has cutouts to fit two different diameters of handle. This is designed to mount on the Ikea TISKEN...

I made a shaving brush and old school safety razor holder. The version that you see on the picture was printed before I made some extra minor tweaks. The construction is made with structural strength in mind so I don't think it needs much...

The original design didn't have appropriate tolerances for my printer, so the print wouldn't fit inside itself. I designed this with a 0.4mm tolerance, as I've found this to be a pretty good fit. ...I also strengthened the male end as it snapped very...

Customized version of https://www.thingiverse.com/thing:3368938 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3368938

Customized version of https://www.thingiverse.com/thing:3368938 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3368938

it's a brush and razor orizzontal holder, fast nice and confortable in use.

... and when I discovered that a pack of fifteen cartriges was now 45 dollars I switched to a Edwin Jagger DE safety razor. ...This holds my razor and shaving brush from my counter. ...I purchased the suction cups from walmart in the hardware section.

This model is especially designed for Edwin Jager DE89 Razor and a shaving Brush

A holder for a shaving brush and safetyrazor. ... Printed laying down with tree supports.

It has a stand that can hold an Escali brush and a Preserve razor, and a soapdish that will hold a puck of shaving soap. To make it a little more compact, I made it so the stand will nestle into the top of the soapdish. There's also an option to...

I wanted to zip tie Tigglebitties shaving brush holder inside a bathroom basket that I use for my shaving gear so I added some holes in the backing plate. I also made a razor holder companion. ... These probably would work for screws as well.

Holder for razor and shaving brush, made in two parts (top and base), for 3d printer

Holder for razor and shaving brush. The cut out for the shelf is 16,5 mm and the hole for the razor has a Diameter of 13 mm. ... I polished the 13 mm hole with my Dremel to perfect fit.

Simple wall stand with drip tray for shaving brush and razor

Customized version of https://www.thingiverse.com/thing:3368938 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3368938