razor and brush stand 3d models
2354141 3d models found related to razor and brush stand.
cults3d
A modern take on the classic double-edged razor and brush stand. Notes: I have included three upper plates to accommodate varying brush handle sizes. Upper plate openings for brush: 28.75mm, 30mm, 32mm. 28.75mm brush opening is a perfect fit for a...
thingiverse
I love the original [Safety Razor and Brush Stand](https://www.thingiverse.com/thing:3655795) made by [ljblk](https://www.thingiverse.com/ljblk/designs), but I wanted to mirror the top so that the brush was on the left and the razor was on the right....
thingiverse
Edit it online https://tinkercad.com/things/h31fj3GpuZP Instructions The hexagonal area at the top is where the brush goes, bristle up. The hole in the top that leads to the inside, which is hollow, is where either the cartridge, single edge, double...
thingiverse
I created this shave brush / safety razor stand. ... The stand can be flipped to use as a cup to soak your brush and wash your razor.
thingiverse
Razor and brush clicks in place, so it will not accidentially slide of the stand. ... Designed from scratch, but inspired by http://www.thingiverse.com/thing:126681 Instructions Print using support...
thingiverse
A basic stand for holding a shaving safety razor and brush. ... Printed it on it's side with supports for the couple of gaps.
thingiverse
Simple stand for holding your double edge razor and soap brush for drying. Should hold most types. ...Print the three pieces and they should press-fit together without the need for adhesive.
thingiverse
Simple one piece design to hold a double edge safety razor and brush.
thingiverse
10 mm diameter handle and brush with 29 mm handle. ...Print Settings Printer Brand: RepRap Printer: Folger Tech i3...
thingiverse
Support needed for the holes, I sliced with creawesome at standard quality and it turned out fine. The model I uploaded is about 5mm higher than the photo I used - I'll update when I re-print. ... Would love to see a make with wood PLA :)
cults3d
This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/h31fj3GpuZP
thingiverse
I needed a stand for my new brush and razor so I whipped up a design rather quickly. This uses 5 mm carbon rod for support. You can cut the rod at different lengths depending on you brush/razor. Its a simplistic design that uses very little material....
thingiverse
Rotate so its laying flat and print with supports. ... Works with Rockwell 6s/6c or Merkur 34c razors.
thingiverse
This thing was made with Tinkercad. Edit it online https://tinkercad.com/things/dnkILQonT38 Enjoy! ...I have included a copy of this file on its side for easier printing.
thingiverse
**BEFORE** printing the front part, turn it. For this model you will need two 8mm tubes. ...Adapt the length to your needs.
thingiverse
This remix was done to fit my particular brush and razor; as well as to add a fillet to the post which had a tendency to snap off at the bottom without it.
thingiverse
Designed for my particular razor, bowl, and brush, but you can fork the Onshape document here if you wish (or export as STEP/IGES and edit externally):...
thingiverse
The original design didn't have appropriate tolerances for my printer, so the print wouldn't fit inside itself. I designed this with a 0.4mm tolerance, as I've found this to be a pretty good fit. ...I also strengthened the male end as it snapped very...
thingiverse
Razor Stand Remix Started fooling around with fusion 360 and decided to make something useful
thingiverse
A simple stand for a Mühle R106 safety razor and hjm pure bristle shaving brush. ... Print Settings Printer: Velleman K8400 Rafts: ...
myminifactory
Brush and razor stand. ... Brush slot is ~30mm (1 1/8") Razor Slot is ~14mm (1/2")
thingiverse
... durable, also i have deleted round recess for more durable and compatibility with other bowls. ... Printed 114% bigger (all axis) fits perfectly to Omega brush and Gillette King C razor. ... Use 2 drops of some "super glue" to join parts together.
thingiverse
Stylish and functional safety razor stand and shave brush base. Stable and secure. Jagger 89 and Rockwell 6s pictured with plenty of room to accommodate other DE razors. Shaving brushand plate holders have internal standoffs to help keep out of...
thingiverse
Hallowed out the back to print faster. ...Printing on its back seems to be the fastest way.
thingiverse
https://www.prusaprinters.org/prints/31485-shaving-stand-for-brush-and-razor UPDATED Recently updated with stronger support at the top and a better sharper bottom for printing. Print instructions Printed in PLA Filamentum Ivory White. ... ...
prusaprinters
So I made a new one a little bigger and the top part is angled up to hold in the brush and razor better.UPDATEDRecently updated with stronger support at the top and a better sharper bottom for printing.Print instructionsPrinted in PLA Filamentum...
thingiverse
Stand re-designed to fit 26mm badger brush and MERKUR Solingen Progress Adjustable 2-Piece Double Edge Safety Razor.
thingiverse
This is a quick stand I made to hold a shaving brush (32 mm Diameter) and safety razor (14.5 mm) I would advise printing it on the right or left side to minimize the chance of it breaking if it gets dropped.
prusaprinters
This is a quick stand I made to hold a shaving brush (32 mm Diameter) and safety razor (14.5 mm) I would advise printing it on the right or left side to minimize the chance of it breaking if it gets dropped. Category: Bathroom