razor blade scraper with handle 3d models
2765900 3d models found related to razor blade scraper with handle.cults3d
M3 nuts (2x) M3x5 countersunk screws (2x) Super Stainless Razor Blade (1x) Tip: In the area of the razor blade must be slightly reworked after printing or touched up with a cutter. ...This has the effect that the razor blade lies better in the...
prusaprinters
It's just flat until it comes up to the tapered edge near the blade.Remember: print as-is, where is, with external support only.Here's a lovely accessory that you may find useful to store the blade...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/c4qRHiZOhBr
thingiverse
A redraw of my earlier scraper, with interior posts to retain the razor more securely. Blade goes over the posts, lid snaps on top, cap slides into the groove on the bottom side of the handle. Be careful when removing the lid to change the blade.
myminifactory
A redraw of my earlier scraper, with interior posts to retain the razor more securely. Blade goes over the posts, lid snaps on top, cap slides into the groove on the bottom side of the handle. Be careful when removing the lid to change the blade.
thingiverse
I liked Mrcleanr6's razor blade scraper for getting under prints on the bed, but my 22mm x 43mm double edged razor blades were too wide and weren't centered in the holder, so I redrew it to fit. While I was at it, I added a slip cover because I am...
thingiverse
... with a 0.4mm nozzle, but a smaller one should work. ... Get the blade started - carefully!! - and then the cap can be used to push it on the rest of the way. The blade might be more or less depending on your printer and extrusion settings. ...
thingiverse
Remixed for scraper blade aka single edge razor blade. Also, now in the shape of a whale, because, Whale! Uses a m3 screw and heat set insert. UPDATE: V2 with a whale tail, because Reddit really wanted one. Also comes in two flavors. ...With...
thingiverse
Razor blade handle with case for hide blade and store spare razor blades. For attachment top handle cover - metric screw: 2x - M2 and 1x M3 or tie a twine. ... Excellent for cutting to fruits, vegetable and decorating homemade bread.
prusaprinters
Razor blade handle with case for hide blade and store spare razor blades.For attachment top handle cover - metric screw: 2x - M2 and 1x M3 or tie a twine.Excellent for cutting to fruits, vegetable and decorating homemade bread.
thingiverse
Fusion 360 remix. ...Ultra comfortable mini razor blade scraper.
thingiverse
Scraper that uses safety razor as a blade. This scraper is made of 3 main parts (scraper, neck and handle). Those are connected and glued together. ... Last two parts (cover and nut) are used to secure the safety razor at place and cover it.
thingiverse
razor blade scraper. specifically for this blade with rounded short ends. ... blade di: W.43.4mm with a radius of 21.7mm center hole 5mm use a m5 screw.and nut to secure.blade.
thingiverse
... to make this one. the blade slides in from the side. the blade is supported top and bottom so it will stay securely in place. print this with no support razor scraper mm.stl has been converted to mm scale. ...razor scraper.stl is modeled in inches
pinshape
SummaryThis scraper is the right size for scraping 3D printer build plates. ...It uses a standard, single-edge razor blade. ...The blade reverses for safe storage.
thingiverse
This scraper is the right size for scraping 3D printer build plates. ...It uses a standard, single-edge razor blade. ...The blade reverses for safe storage.
thingiverse
I wanted a handy scraper with blade with good handling and stability during use. In addition, I wanted a clip on protection. ...You should print it upright.
thingiverse
Simple razor blade scraper great for removing prints from the print bed and scraping glue from glass print bed. Load razor blade from the side of holder. ...you may need to split the first few layers
pinshape
I would recommend printing both parts at 100% (though you might get away printing the blade holder with lower infill percentage), as that makes it a very sturdy non-flexing scraper. You can order the hardware and blade from the following links...
myminifactory
I would recommend printing both parts at 100% (though you might get away printing the blade holder with lower infill percentage), as that makes it a very sturdy non-flexing scraper. You can order the hardware and blade from the following links...
thingiverse
I would recommend printing both parts at 100% (though you might get away printing the blade holder with lower infill percentage), as that makes it a very sturdy non-flexing scraper. ... You can order the hardware and blade from the following links...
youmagine
I would recommend printing both parts at 100% (though you might get away printing the blade holder with lower infill percentage), as that makes it a very sturdy non-flexing scraper. You can order the hardware here: https://bit.ly/2VBpAAh And the...
prusaprinters
My wife wanted the razor blade scraper for cleaning her glass-ceramic plate - then I solved her problem with this simple print Download -> Share -> Print -> Rate -> Donate -> Enjoy -> Thank you Created for printing without supports...
prusaprinters
This is a simple to print and lightweight razor blade scraper, which can be used to release prints from your printbed, scrape paint of tiles, etc. There are only two parts you need to print, with a combined print time of around 5 hours (at 0.1mm...
prusaprinters
A scraper using simple razor blades which is not flimsy or imprecise. ...The blade is held firmly in place. Please be careful when inserting the blade. Strongly inspired by https://www.thingiverse.com/thing:2024019 Use razor blades such as this one:...
cults3d
Simple handle that accommodates the utility blade razor. Uses 3 M3x5 screws or longer if need be for nuts on the bottom.When put into my slicer I need to scale up to 1000% so double check your scale before printing. I printed in PETG at 100% infill...
thingiverse
Because my wife wanted to have something to hold the razor blade when she wants to remove limestone.... I did it ;-))..... ... Instructions Nut dimension m4 There is a removable part, on the Yellow...
thingiverse
Update 3/15/20 Added two versions one with a thicker handle and another with a thicker handle and a spot for two 10mm neodieminum magnets I use the magnets to stick it to the side of my printer for easy finding. This is a great design that someone...