rc 1 10 3d models

Anka is a mostly 3d printed 1/10 RC Short Course Truck which is inspired and remixed from the excellent Tarmo4 project. (You may reach the Tarmo4 project's details from here.) If you are a terrible driver like me, this hobby might become a bit...

Hello and welcome to the 1/10 scale Toyota Hilux (third gen) inner body panel set. This model was designed using the HG P407 shell as the base. This shell is a clone of the Tamiya Hilux, bruiser, mountaineer and RC4WD Mojave cab. As such the model...

This is a replacement bumper, designed for the Laegendary Legend 1:10 RC Car. 100% compatible with factory parts! The factory bumper uses 2 screws, Since 3d Printed parts tend to not be as flexible, i've designed the mount to use 4 screws. The...

This was designed to work with Dukedoks 1/10 chassis project, but it may also work with traditional 1/10 chassis with a 12mm hex. Chassis:https://cults3d.com/en/3d-model/game/casis-1-10-adaptable Fits together using 10 M2 x 8mm bolts. ...I recommend...

... 65mm outside diam. 73 Inside 12mm hex Printing: Layer height: 0.2 Infill: 55% Support: tree Slicer: Cura 4.9.1 Material: PLA - but I am sure ABS would be better Printed hex down on my first test, and it worked fine, should work ok either way.

This is the BMW E24 M635csi RC car body is fit for 255mm to 260mm wheelbase RC car any problem please let me know.

Anka is a mostly 3d printed 1/10 RC Short Course Truck which is inspired and remixed from the excellent Tarmo4 project. (You may reach the Tarmo4 project's details from here.)If you are a terrible driver like me, this hobby might become a bit...

This is a replacement bumper, designed for the Laegendary Legend 1:10 RC Car. 100% compatible with factory parts! The factory bumper uses 2 screws, Since 3d Printed parts tend to not be as flexible, i've designed the mount to use 4 screws. The...

The design was originally intended as a dual cab with 4 doors and a 4x4 drivetrain, it is made to fit on 1/10 scale RC crawlers with a wheelbase of 420mm and tyre height of 120mm for true scale proportions. It is also recommended to have a tyre to...

PARMATreD PT4Fully 3D Printed 1/10 car with 540 motorEasy to build (Instructions Manual attached)Easy to repairCheap ComponentsSpeed>20 km/hIdeal for fun, drift, education

PARMATreD PT4Fully 3D Printed 1/10 car with 540 motorEasy to build (Instructions Manual attached)Easy to repairCheap ComponentsSpeed>20 km/hIdeal for fun, drift, education

Designed for a 1/10 scale look but you can most likely scale it up or down although smaller may create really thin walls.

This replacement part perfectly matches the Tamiya DF-02 chassis and can be used on numerous other 1:10 scale models.

Jerry can RC truck mount that matches Ossum's Jerry cans. Included holes for strap, with 2 slightly different versions. I recommend PETG, but I've printed it in PLA successfully. I suggest printing with THICK walls and/or 100% infill. Printing...

RC Enthusiasts Unite 1993 Camel Trophy Squad Logos Get a New Look Revised Designs for RC, Scale, and Crawler Fans Average Logo Size: 6 inches by 3 inches, 0.08 inches Thick

PARMATreD PT4 Fully 3D Printed 1/10 car with 540 motor Easy to build (Manual attached) Easy to repair Cheap Components Speed>20 km/h Ideal for fun, drift, education

1/10 scale wheel faces made to work with MST adjustable offset barrels. Wheel faces may require the axle hole be widened slightly for a cleaner fit. ... Printed face up with bed supports on.

Designed myself based off a real size sand ladder scaled down to 1/10 scale Has 4 holes for mounting, these can be opened up for using M3 screws

It's also compatible with other cars such as the Redcat Volcano EPX Pro, HSP Brontosaurus, Exceed Infinitive, Himoto EMXT-1, and Amewi Torche Pro, which are essentially identical models. The body is split into two pieces to accommodate most...

This is an RC stand adapter I made up really quick in order to be able to support RC crawlers on my RC stand (stand is made by Hobby park). It fits my cars decently but I did notice that each crawler sits a bit differently. Also I put the felt side...

Interiores de puertas bien detalladas El archivo se encuentra en escala 1:10 con un espesor mínimo de 2.5 milímetros, lo que lo hace ideal para poder ser escalado hasta 1:24, teniendo un espesor de 1 milímetro. ...Para conseguir la escala deseada usa...

(Truck body is sold separately) https://cults3d.com/en/3d-model/game/crawler-4320-1-10-rc-body https://cults3d.com/en/3d-model/game/ahead-rc-crawler-4320-dual-cab The wheelbase is designed for use with Traxxas’ TRX6 platform, i.e. 324mm from front to...

UPDATE: .DXF files for all windows are now available for download here: https://www.aheadrc.com/dxf-files With high amounts of detail and shaping, the body is made to look as realistic as possible, and is designed for the standard 313mm or 12.3in...

Human: I give a rating of one out of ten for the quality of this RC wheel, which measures 120 millimeters in length.

This is a scale petrol generator for your RC car/garage diorama equipment. ... Update: I added a split model to try printing separately.

THIS SNORKEL WAS DESIGN FOR THE VITARA RC BODY MST CMX. ... IF YOU WANT TO DO A PAINT JOB FOR A REALISTIC FINISH.

Sliders for HG P415 or P408 hummer / humvee RC cars. ... Print with 100% infill Supports needed Best to print in PLA+ or ABS for better durability.

Links for items;...

... 360. ...To achieve a realistic scale representation, the design was halved down to 1/10 of its original size. ...Notably, a robust 12mm hex drive was integrated into the mechanism, while the overall diameter measured in at an impressive 2.1 inches.

Parcel shelf for RC drift car This fits perfectly in my Pandora Origin Labo S14 but can easily be trimmed to fit others Print flat with 15% infill I used PLA+ at 195/65 I use a Brim to make sure it prints flat. ... Check out my insta for more projects...