rc 135 model
2078677 3d models found related to rc 135 model.cgtrader
... using Rhinoceros 5, but SolidWorks files are provided along with STL formats for the individual components to maintain simplicity. As a whole, this model is built to exact scale specifications and accurately represents each of its components.
thingiverse
I scaled up a model from https://www.thingiverse.com/thing:3411464/files courtesy of tahustvedt, and I appreciate the nice work. ... You might want to check out these links: https://www.youtube.com/watch?v=WTSOVJ_5Ybk...
cults3d
About 1/25 (scale to fit your model) Length: 19,00 x 93,09 x 3,65 mm Short: 19,00 x 79,84 x 3,65 mm Flip on slicer to get the other side Diameter: approx 2.5 mm For commercial use of the files, contact me first Attention: -Take care when you remove...
thingiverse
Designed an alternative engine cover for more thrust and better motor cooling for my AF-Model Sky Surfer. The V01 is lighter than the V04, but the V04 is also an engine support to stop the wooden engine mount from bending. Just glue it on with a...
thingiverse
Get ready to take your flying skills to new heights with our cutting-edge FPV kit designed specifically for the fully 3D printed seaplane and taildragger plane, Eclipson Model T. This revolutionary system is poised to revolutionize your flight...
cgtrader
Takeoff speed: twelve meters per second (four-kilogram model) or fifteen meters per second (six-kilogram model). Maximum angle of attack: twenty-five degrees without slat, or more than forty degrees with slat. All parts have been proven to fit...
myminifactory
That repair allowed me to put my Arduino Bluetooth controlled model car back on its wheels and finish it. It was printed with support material because its about 2mm higher at the front than the back. Its thickness is around 5mm, I kept the support...
cults3d
... wide and consists of 60 parts. In the photos I photographed the prototype of this chair before its final phase, but the differences are not big from the final model. ...It is easy to assemble, the parts are distributed in different folders for ease!
thingiverse
I made this keel for the Catamaran model of MalinaPlHere; https://www.thingiverse.com/thing:5944386I know it makes the model different than the original boat but it will be underwater :)Although the keel is normally used for balance on sailing boats,...
cgtrader
It features rear wheel drive model, forward motor configuration, and realistic suspension similar to a real automobile. For assembly, you will also require non-print parts: bolts, bearings, and electronics such as motors, batteries, chargers, radios,...
cgtrader
The model features an integrated bilge pump to the turbine. The turbine is on two axes, left and right, as well as up and down, allowing the hull to be pressed at high speed or lifted to pass waves and return against the current. Reverse gear is...
cults3d
https://www.youtube.com/watch?v=pv5GI4Le0rI ALL PLA 1:16 T-34/85 model capable of R/C. Features 360deg Turret traverse and magnetic suspension. -ALL PLA -Maximizes Printed Parts -Limits parts required for build (M3 screws/Magnets/Bearings)...
cults3d
This is another Polish WW2 fighter - PZL P.50 Jastrzab (Hawk) -https://pl.wikipedia.org/wiki/PZL.50_Jastrz%C4%85b As usual (and as all our models) the design is dedicated for vase mode printing. LW-PLA for nose/tail and wingtips. Impact...
cgtrader
In that spirit, this 3D-printed R/C model can optionally be equipped with an Ardupilot flight controller to enable assisted and autonomous flight features. ... • Build guide • Hardware pack • Sample part • Gear sequencer pecifications: • Wingspan:...
cults3d
A set of parts and components for the manufacture of RC aircraft models. ...This collection will be updated, you can support my motivation for Patreon and get more models for 3D printing therehttps://www.patreon.com/posts/rocker-for-f2b-31849457
thingiverse
I'd love to build a custom model for you, just as the creator did on http://www.thingiverse.com/thing:497435 with the help of Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=497435. Let me guide you through it! You're going to...
thingiverse
This project started from the idea to make a printer bed, a customized version of the popular online community for sharing 3D models. With the help of Customizer! I managed to tailor it exactly how I needed. Now, let me tell you how to put this...
cults3d
... (z kufra), toto logo si môžeš zakúpiť a tým podporiť moju tvorbu. Bolo to modelované na základe originálnej predlohy Ak chceš verziu 135/130 napíš mi správu, pošlem model osobne. ...Cena je za jeden nápis, buď 135/130/136, každý ďaľší model je 13€.
thingiverse
Get ready to take your RC aircraft model building skills to new heights with this exciting collection of parts and components. As the collection continues to grow, you can stay up-to-date on the latest additions by supporting my creative endeavors...
grabcad
A propeller designed specifically for remote control (RC) devices like quad-copters is what's needed.